On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote: > On Tue, Jan 29 2008, Jens Axboe wrote: > > On Tue, Jan 29 2008, Oliver Neukum wrote: > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe: > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[EMAIL PROTECTED]> > > > > > wrote: > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > > > > > >> Greg KH wrote: > > > > > > > > > No difference, still just a lot of resets. > > > > > > > > > > > Where you able to figure out which usb storage transport is used? > > > > > > > > > > in drivers/usb/storage/usb.c you have get_protocol() and > > > > > get_transport() > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This > > > > > will > > > > > pinpoint better where to look. Let me research a bit. > > > > > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and > > > > transport is 'Bulk' > > > > > > You can recompile your kernel with CONFIG_USB_DEBUG and > > > CONFIG_STORAGE_DEBUG > > > That should tell the reason for the resets. > > > > Sure, I'll do that. Will post the results tonight. > > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged > in the device, waited 10 seconds or so and pulled it out. These are the > messages. > > It all looks good until the MODE_SENSE command, where it only transfers > 4 of 192 bytes.
No, that's not the problem. This is the problem:
> usb-storage: *** thread awakened.
> usb-storage: Command TEST_UNIT_READY (6 bytes)
> usb-storage: 00 00 00 00 00 00
> usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> usb-storage: Status code 0; transferred 31/31
> usb-storage: -- transfer complete
> usb-storage: Bulk command transfer result=0
> usb-storage: Attempting to get CSW...
> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> usb-storage: Status code 0; transferred 13/13
> usb-storage: -- transfer complete
> usb-storage: Bulk status result = 0
> usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> usb-storage: -- transport indicates command failure
> usb-storage: Issuing auto-REQUEST_SENSE
> usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> usb-storage: Status code 0; transferred 31/31
> usb-storage: -- transfer complete
> usb-storage: Bulk command transfer result=0
> usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> usb-storage: usb_sg_init returned -22
> usb-storage: Bulk data transfer result 0x4
> usb-storage: -- auto-sense failure
> usb-storage: storage_pre_reset
> ehci_hcd 0000:00:1d.7: port 1 high speed
> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> ehci_hcd 0000:00:1d.7: port 1 high speed
> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> usb-storage: storage_post_reset
> usb-storage: usb_reset_composite_device returns 0
> usb-storage: scsi cmd done, result=0x70000
> usb-storage: *** thread sleeping.
For some reason, usb_sg_init is boned during auto-sense.
Matt
--
Matthew Dharm Home: [EMAIL PROTECTED]
Maintainer, Linux USB Mass Storage Driver
It was a new hope.
-- Dust Puppy
User Friendly, 12/25/1998
pgpb4Ng6xEurV.pgp
Description: PGP signature
