On Mon, Jun 24, 2019 at 07:40:12PM +0200, Oliver Graute wrote:
> This patch adds support for the i.MX6UL variant of the Variscite DART-6UL
> SoM Carrier-Board
>
> Signed-off-by: Oliver Graute <[email protected]>
> ---
> .../boot/dts/imx6ul-imx6ull-var-dart-common.dtsi | 458
> +++++++++++++++++++++
> 1 file changed, 458 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6ul-imx6ull-var-dart-common.dtsi
>
> diff --git a/arch/arm/boot/dts/imx6ul-imx6ull-var-dart-common.dtsi
> b/arch/arm/boot/dts/imx6ul-imx6ull-var-dart-common.dtsi
> new file mode 100644
> index 0000000..57d62e8
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-imx6ull-var-dart-common.dtsi
> @@ -0,0 +1,458 @@
> +// SPDX-License-Identifier: (GPL-2.0)
> +/dts-v1/;
> +
> +#include "imx6ul.dtsi"
> +/ {
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + touch_3v3_regulator: regulator-touch-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "touch_3v3_supply";
> + regulator-always-on;
> + };
> +
> + reg_sd1_vmmc: regulator-sd1-vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + reg_gpio_dvfs: regulator-gpio {
> + compatible = "regulator-gpio";
> + regulator-min-microvolt = <1300000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "gpio_dvfs";
> + regulator-type = "voltage";
> + gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
If it's active-high, I think you need enable-active-high property.
> + states = <1300000 0x1 1400000 0x0>;
> + };
> +
> + clk-phy {
You do not need this container node.
> + /* ref_clk for micrel ethernet phy */
> + rmii_ref_clk: rmii_ref_clk_grp {
The node name could be better named, because:
1. We prefer to use hyphen than underscore in node name.
2. Not sure why the '_grp' suffix is there.
Something like 'clock-rmii-ref' might be better.
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <25000000>;
> + clock-output-names = "rmii-ref";
> + };
> + };
> +
> + clk-pll {
> + assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
> + assigned-clock-rates = <786432000>;
> + };
Not sure what this node is about and how it works.
> +};
> +
> +&adc1 {
> + vref-supply = <&touch_3v3_regulator>;
> + status = "okay";
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + status = "disabled";
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + status = "disabled";
> +};
> +
> +&cpu0 {
> + arm-supply = <®_arm>;
> + soc-supply = <®_soc>;
> + dc-supply = <®_gpio_dvfs>;
What is this 'dc-supply'? I'm not sure cpufreq driver supports it.
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet1>;
> + phy-mode = "rmii";
> + status = "disabled";
> +};
> +
> +&fec2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet2>;
> + phy-mode = "rmii";
> + status = "disabled";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + micrel,rmii-reference-clock-select-25-mhz;
> + clocks = <&rmii_ref_clk>;
> + clock-names = "rmii-ref";
> + reg = <1>;
> + };
> +
> + ethphy1: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + micrel,rmii-reference-clock-select-25-mhz;
> + clocks = <&rmii_ref_clk>;
> + clock-names = "rmii-ref";
> + reg = <3>;
> + };
> + };
> +};
> +
> +&gpmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpmi_nand>;
> + fsl,legacy-bch-geometry;
Are you sure this property is supported by mainline kernel?
> + status = "okay";
> +
> + partition@0 {
> + label = "spl";
> + reg = <0x00000000 0x00200000>;
> + };
> +
> + partition@200000 {
> + label = "uboot";
> + reg = <0x00200000 0x00200000>;
> + };
> +
> + partition@400000 {
> + label = "uboot-env";
> + reg = <0x00400000 0x00200000>;
> + };
> +
> + partition@600000 {
> + label = "kernel";
> + reg = <0x00600000 0x00800000>;
> + };
> +
> + partition@e00000 {
> + label = "rootfs";
> + reg = <0x00e00000 0x3f200000>;
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "disabled";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "disabled";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "disabled";
> +};
> +
> +&sai2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sai2>;
> + assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
> + <&clks IMX6UL_CLK_SAI2>;
> + assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
> + assigned-clock-rates = <0>, <12288000>;
> + fsl,sai-mclk-direction-output;
> + status = "okay";
> +};
> +
> +&snvs_poweroff {
> + status = "okay";
> +};
> +
> +&snvs_rtc {
> + status = "disabled";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "disabled";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + uart-has-rtscts;
> + status = "disabled";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + uart-has-rtscts;
> + status = "disabled";
> +};
> +
> +&usbotg1 {
> + disable-over-current;
> + status = "disabled";
> +};
> +
> +&usbotg2 {
> + disable-over-current;
> + status = "disabled";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + no-1-8-v;
> + keep-power-in-suspend;
> + vmmc-supply = <®_sd1_vmmc>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog_1>;
Where is this pinctrl_hog_1 defined?
> +
> + pinctrl_enet1: enet1grp {
> + fsl,pins = <
> + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
> + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
> + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
> + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
> + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
> + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
> + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
> + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
> + >;
> + };
> +
> + pinctrl_enet2: enet2grp {
> + fsl,pins = <
> + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
> + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
> + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
> + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
> + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
> + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
> + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
> + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031
> + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
> + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
> + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x1b0b0
> + >;
> + };
> +
> + pinctrl_flexcan1: flexcan1grp{
> + fsl,pins = <
> + MX6UL_PAD_LCD_DATA09__FLEXCAN1_RX 0x1b020
> + MX6UL_PAD_LCD_DATA08__FLEXCAN1_TX 0x1b020
> + >;
> + };
> +
> + pinctrl_flexcan2: flexcan2grp{
> + fsl,pins = <
> + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
> + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
> + >;
> + };
> +
> + pinctrl_gpio_leds: gpioledsgrp {
> + fsl,pins = <
> + MX6UL_PAD_CSI_HSYNC__GPIO4_IO20 0x1b0b0
> + MX6UL_PAD_GPIO1_IO00__GPIO1_IO00 0x17059
> + >;
> + };
> +
> + pinctrl_gpmi_nand: gpminandgrp {
> + fsl,pins = <
> + MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0xb0b1
> + MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0xb0b1
> + MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0xb0b1
> + MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0xb000
> + MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0xb0b1
> + MX6UL_PAD_NAND_CE1_B__RAWNAND_CE1_B 0xb0b1
> + MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0xb0b1
> + MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0xb0b1
> + MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0xb0b1
> + MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0xb0b1
> + MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0xb0b1
> + MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0xb0b1
> + MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0xb0b1
> + MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0xb0b1
> + MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0xb0b1
> + MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0xb0b1
> + >;
> + };
> +
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT 0x03029
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
> + MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
> + MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
> + >;
> + };
> +
> + pinctrl_lcdif_dat: lcdifdatgrp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
> + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
> + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
> + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
> + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
> + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
> + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
> + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
> + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
> + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
> + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
> + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
> + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79
> + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79
> + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79
> + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79
> + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79
> + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79
> + >;
> + };
> +
> + pinctrl_lcdif_ctrl: lcdifctrlgrp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
> + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
> + >;
> + };
Is it really needed to split LCDIF pins into data and ctrl groups?
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_DATA00__PWM1_OUT 0x110b0
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
> + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1
> + MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1
> + MX6UL_PAD_UART2_CTS_B__UART2_DCE_CTS 0x1b0b1
> + MX6UL_PAD_UART2_RTS_B__UART2_DCE_RTS 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
> + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
> + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1
> + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
> + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x17059
> + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
> + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
> + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
> + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
> + MX6UL_PAD_CSI_VSYNC__GPIO4_IO19 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> + fsl,pins = <
> + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
> + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
> + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
> + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
> + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
> + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
> + MX6UL_PAD_CSI_VSYNC__GPIO4_IO19 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> + fsl,pins = <
> + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
> + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
> + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
> + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
> + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
> + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
> + MX6UL_PAD_CSI_VSYNC__GPIO4_IO19 0x1b0b1
> + >;
> + };
> +
> + pinctrl_sai1: sai1grp {
Please keep the pinctrl nodes alphabetically sorted.
> + fsl,pins = <
> + MX6UL_PAD_CSI_DATA05__SAI1_TX_BCLK 0x11088
> + MX6UL_PAD_CSI_DATA04__SAI1_TX_SYNC 0x17088
> + MX6UL_PAD_CSI_DATA06__SAI1_RX_DATA 0x11088
> + MX6UL_PAD_CSI_DATA07__SAI1_TX_DATA 0x11088
> + >;
> + };
> +
> + pinctrl_sai2: sai2grp {
> + fsl,pins = <
> + MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
> + MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
> + MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088
> + MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088
> + MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088
> + >;
> + };
> +
> + pinctrl_tsc: tscgrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
> + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
> + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
> + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO08__WDOG1_WDOG_B 0x78b0
> + >;
> + };
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> +};
The iomuxc node is put at the end of the file to improve readability due
to its huge number of pinctrl data. But wdog should find its place per
alphabetic order.
Shawn
> --
> 2.7.4
>
