HI Laurent, On Mon, May 21, 2018 at 04:10:34PM +0300, Laurent Pinchart wrote: > Hi Jacopo, > > On Monday, 21 May 2018 15:33:40 EEST jacopo mondi wrote: > > On Mon, May 21, 2018 at 01:54:55PM +0300, Laurent Pinchart wrote: > > > On Monday, 21 May 2018 12:57:05 EEST jacopo mondi wrote: > > >> On Fri, May 18, 2018 at 06:12:15PM +0300, Laurent Pinchart wrote: > > >>> On Friday, 18 May 2018 17:47:57 EEST Jacopo Mondi wrote: > > >>>> Describe CVBS video input through analog video decoder ADV7180 > > >>>> connected to video input interface VIN4. > > >>>> > > >>>> The video input signal path is shared with HDMI video input, and > > >>>> selected by on-board switches SW-53 and SW-54 with CVBS input > > >>>> selected by the default switches configuration. > > >>>> > > >>>> Signed-off-by: Jacopo Mondi <[email protected]> > > >>>> Reviewed-by: Niklas Söderlund <[email protected]> > > >>>> > > >>>> --- > > >>>> v2 -> v3: > > >>>> - Add comment to describe the shared input video path > > >>>> - Add my SoB and Niklas' R-b tags > > >>>> --- > > >>>> > > >>>> arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 42 ++++++++++++++++++ > > >>>> 1 file changed, 42 insertions(+) > > >>>> > > >>>> diff --git a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts > > >>>> b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts index > > >>>> 9d73de8..95745fc > > >>>> 100644 > > >>>> --- a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts > > >>>> +++ b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts > > >>>> @@ -142,6 +142,11 @@ > > >>>> groups = "usb0"; > > >>>> function = "usb0"; > > >>>> }; > > >>>> + > > >>>> + vin4_pins_cvbs: vin4 { > > >>>> + groups = "vin4_data8", "vin4_sync", "vin4_clk"; > > >>>> + function = "vin4"; > > >>>> + }; > > >>>> }; > > >>>> > > >>>> &i2c0 { > > >>>> @@ -154,6 +159,23 @@ > > >>>> reg = <0x50>; > > >>>> pagesize = <8>; > > >>>> }; > > >>>> + > > >>>> + analog-video@20 { > > >>>> + compatible = "adi,adv7180"; > > >>>> + reg = <0x20>; > > >>>> + > > >>>> + port { > > >>> > > >>> The adv7180 DT bindings document the output port as 3 or 6 > > >>> (respectively for the CP and ST versions of the chip). You should thus > > >>> number the port. Apart from that the patch looks good. > > >> > > >> I admit I have barely copied this from Gen-2 boards DTS, but reading > > >> the driver code and binding description again, I think this is > > >> correct, as the output port numbering and mandatory input port (which > > >> is missing here) only apply to adv7180cp/st chip versions. > > >> > > >> Here we describe plain adv7180, no need to number output ports afaict. > > > > > > Indeed, my bad. > > > > > > Shouldn't you however use "adi,adv7180cp" as that's the chip we are using > > > ? > > > The "adi,adv7180" has no port documented in its DT bindings, so it > > > shouldn't have any port node at all. > > > > I'm a bit confused here. > > > > The only Gen-2 board using the "adi,adv7180cp" compatible string is > > Gose, which is also the only one I can get schematics for. That board > > indeed feature an ADV7180WBCP32Z, as the Draak does. I cannot get > > schematics for any other Gen-2 board, to compare the ADV7180 variant > > installed there. If anyone can confirm that all other Gen-2 board uses > > a different version (or that all other Gen-2 board DTS file use a > > wrong compatible string value), I'll re-send this with a different > > compatible value and proper port nodes numbering. > > Other Gen2 boards use a ADV7180WBCP32Z as well. The issue here isn't that the > chip you're trying to support is different. The DT bindings that were > initially written for the adi,adv7180 didn't have port nodes. When it was time > to add them, we realized that two variants of the chip existed with different > connectivity. We have thus added two new compatible strings to differentiate > them, with different port numbers. The old compatible string should be > deprecated in favour of the new ones. >
Ack, thanks for explaining.
I don't have any Gen2 board here, but if someone is willing to test, I
can change the Gen2 bindings to use the new version in a follow-up
series.
Thanks
j
> > >>>> + /*
> > >>>> + * The VIN4 video input path is shared between
> > >>>> + * CVBS and HDMI inputs through SW[49-54]
> > >>>> switches.
> > >>>> + *
> > >>>> + * CVBS is the default selection, link it to
> > >>>> VIN4 here.
> > >>>> + */
> > >>>> + adv7180_out: endpoint {
> > >>>> + remote-endpoint = <&vin4_in>;
> > >>>> + };
> > >>>> + };
> > >>>> + };
> > >>>> };
> > >>>>
> > >>>> &i2c1 {
> > >>>> @@ -246,3 +268,23 @@
> > >>>> timeout-sec = <60>;
> > >>>> status = "okay";
> > >>>> };
> >>>> +
> > >>>> +&vin4 {
> > >>>> + pinctrl-0 = <&vin4_pins_cvbs>;
> > >>>> + pinctrl-names = "default";
> > >>>> +
> > >>>> + status = "okay";
> > >>>> +
> > >>>> + ports {
> > >>>> + #address-cells = <1>;
> > >>>> + #size-cells = <0>;
> > >>>> +
> > >>>> + port@0 {
> > >>>> + reg = <0>;
> > >>>> +
> > >>>> + vin4_in: endpoint {
> > >>>> + remote-endpoint = <&adv7180_out>;
> > >>>> + };
> > >>>> + };
> > >>>> + };
> > >>>> +};
>
> --
> Regards,
>
> Laurent Pinchart
>
>
>
signature.asc
Description: PGP signature
