On Thu, Sep 21, 2017 at 11:26:04AM -0500, Rob Herring <[email protected]> wrote:
> On Wed, Sep 20, 2017 at 4:27 PM, Serge Semin <[email protected]> wrote:
> > On Wed, Sep 20, 2017 at 03:52:55PM -0500, Rob Herring <[email protected]>
> > wrote:
> >> On Sat, Sep 16, 2017 at 01:42:19PM +0300, Serge Semin wrote:
> >> > This parameters may be varied in accordance with hardware specifics.
> >> > So lets add the corresponding settings to the usb251x driver dts
> >> > specification.
> >> >
> >> > Signed-off-by: Serge Semin <[email protected]>
> >> > ---
> >> > Documentation/devicetree/bindings/usb/usb251xb.txt | 6 ++++++
> >> > drivers/usb/misc/usb251xb.c | 20
> >> > ++++++++++++++++----
> >> > 2 files changed, 22 insertions(+), 4 deletions(-)
> >> >
> >> > diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt
> >> > b/Documentation/devicetree/bindings/usb/usb251xb.txt
> >> > index 3d84626d3..dd59a32e7 100644
> >> > --- a/Documentation/devicetree/bindings/usb/usb251xb.txt
> >> > +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt
> >> > @@ -44,6 +44,12 @@ Optional properties :
> >> > device connected.
> >> > - sp-disabled-ports : Specifies the ports which will be self-power
> >> > disabled
> >> > - bp-disabled-ports : Specifies the ports which will be bus-power
> >> > disabled
> >> > + - sp-max-{power,current} : Indicates the power/current consumed by hub
> >> > from
> >> > + an upstream port (VBUS) when operation as a self-powered hub. The
> >> > value
> >> > + is given in mA in a 0 - 100 range (default is 1mA).
> >> > + - bp-max-{power,current} : Indicates the power/current consumed by hub
> >> > from
> >> > + an upstream port (VBUS) when operation as a bus-powered hub. The
> >> > value
> >> > + is given in mA in a 0 - 510 range (default is 100mA).
> >>
> >> These need units as defined in property-units.txt.
> >>
> >
> > Ok.
> >
> >> Why do you need power and current? Can't you calculate power?
> >>
> >
> > These are different parameters of the device. They got different
> > configuration
> > registers and descriptions:
> > max_power* - ... This value also includes the power consumption of a
> > permanently attached peripheral if the hub is configured as a compound
> > device, and the embedded peripheral reports 0mA in its descriptors.
> > max_current* - ... This value does NOT include the power consumption of a
> > permanently attached peripheral if the hub is configured as a compound
> > device.
>
> Then the names here should somehow reflect the above. Perhaps
> "composite-current" and "hub-current" or something like that.
>
I left the naming in accordance with the device datasheet. I thought it would be
better since the driver user would still need to consult with the device
documentation to properly set them. I don't really get how the difference is
reflected
with the naming declared there though. So what naming would you prefer then?
Might be
something like:
{sp,bp}-max-total-current - for so named {sp,bp}-max-power, since it includes
all the
permanently attached peripherals.
{sp,bp}-max-removable-current - for so named {sp,bp}-max-current, since it
doesn't
include the permanently attached peripherals.
Or is it better to leave it in compliance with the documentation naming?
> >
> > Additionally as you can see, they both are measured in "mA", so it isn't
> > a real physical power.
>
> Well, I can't because there's no units.
>
What this line means then?
- sp-max-{power,current} : ... The value is given in mA in a 0 - 100 range
(default is 1mA).
- bp-max-{power,current} : ... The value is given in mA in a 0 - 510 range
(default is 100mA).
Maybe I don't know something and the description line should state the units
somehow
clearer?
> Rob
