On Sun, Dec 18, 2016 at 11:17:56PM -0800, Andrey Smirnov wrote:
> Add .dts file for rev. C of the board by factoring out commonalities
> into a shared include file (vf610-zii-dev-rev-b-c.dtsi) and deriving
> revision specific file from it (vf610-zii-dev-rev-b.dts and
> vf610-zii-dev-reb-c.dts).
>
> Signed-off-by: Andrey Smirnov <[email protected]>
<snip>
> +/ {
> + model = "ZII VF610 Development Board, Rev C";
> + compatible = "zii,vf610dev-c", "zii,vf610dev", "fsl,vf610";
> +
> + mdio-mux {
> + compatible = "mdio-mux-gpio";
> + pinctrl-0 = <&pinctrl_mdio_mux>;
> + pinctrl-names = "default";
> + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH
> + &gpio0 9 GPIO_ACTIVE_HIGH
> + &gpio0 25 GPIO_ACTIVE_HIGH>;
> + mdio-parent-bus = <&mdio1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio_mux_1: mdio@1 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch0: switch0@0 {
Drop the zero in node name.
switch0: switch@0
> + compatible = "marvell,mv88e6190";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + dsa,member = <0 0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + label = "cpu";
> + ethernet = <&fec1>;
Please have a newline between properties and child node.
Shawn
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + label = "lan1";
> + };
> +
> + port@2 {
> + reg = <2>;
> + label = "lan2";
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "lan3";
> + };
> +
> + port@4 {
> + reg = <4>;
> + label = "lan4";
> + };
> +
> + switch0port10: port@10 {
> + reg = <10>;
> + label = "dsa";
> + phy-mode = "xgmii";
> + link = <&switch1port10>;
> + };
> + };
> + };
> + };
> +
> + mdio_mux_2: mdio@2 {
> + reg = <2>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch1: switch1@0 {
> + compatible = "marvell,mv88e6190";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + dsa,member = <0 1>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <1>;
> + label = "lan5";
> + };
> +
> + port@2 {
> + reg = <2>;
> + label = "lan6";
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "lan7";
> + };
> +
> + port@4 {
> + reg = <4>;
> + label = "lan8";
> + };
> +
> +
> + switch1port10: port@10 {
> + reg = <10>;
> + label = "dsa";
> + phy-mode = "xgmii";
> + link = <&switch0port10>;
> + };
> + };
> + };
> + };
> +
> + mdio_mux_4: mdio@4 {
> + reg = <4>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> +};
> +
> +&dspi0 {
> + bus-num = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_dspi0>;
> + status = "okay";
> + spi-num-chipselects = <2>;
> +
> + m25p128@0 {
> + compatible = "m25p128", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + };
> +
> + atzb-rf-233@1 {
> + compatible = "atmel,at86rf233";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctr_atzb_rf_233>;
> +
> + spi-max-frequency = <7500000>;
> + reg = <1>;
> + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-parent = <&gpio3>;
> + xtal-trim = /bits/ 8 <0x06>;
> +
> + sleep-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
> + reset-gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;
> +
> + fsl,spi-cs-sck-delay = <180>;
> + fsl,spi-sck-cs-delay = <250>;
> + };
> +};
> +
> +&i2c0 {
> + /*
> + * U712
> + *
> + * Exposed signals:
> + * P1 - WE2_CMD
> + * P2 - WE2_CLK
> + */
> + gpio5: pca9557@18 {
> + compatible = "nxp,pca9557";
> + reg = <0x18>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + /*
> + * U121
> + *
> + * Exposed signals:
> + * I/O0 - ENET_SWR_EN
> + * I/O1 - ESW1_RESETn
> + * I/O2 - ARINC_RESET
> + * I/O3 - DD1_IO_RESET
> + * I/O4 - ESW2_RESETn
> + * I/O5 - ESW3_RESETn
> + * I/O6 - ESW4_RESETn
> + * I/O8 - TP909
> + * I/O9 - FEM_SEL
> + * I/O10 - WIFI_RESETn
> + * I/O11 - PHY_RSTn
> + * I/O12 - OPT1_SD
> + * I/O13 - OPT2_SD
> + * I/O14 - OPT1_TX_DIS
> + * I/O15 - OPT2_TX_DIS
> + */
> + gpio6: sx1503@20 {
> + compatible = "semtech,sx1503q";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sx1503_20>;
> + #gpio-cells = <2>;
> + #interrupt-cells = <2>;
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
> + gpio-controller;
> + interrupt-controller;
> +
> + enet_swr_en {
> + gpio-hog;
> + gpios = <0 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "enet-swr-en";
> + };
> + };
> +
> + /*
> + * U715
> + *
> + * Exposed signals:
> + * IO0 - WE1_CLK
> + * IO1 - WE1_CMD
> + */
> + gpio7: pca9554@22 {
> + compatible = "nxp,pca9554";
> + reg = <0x22>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + };
> +};
> +
> +&i2c1 {
> + at24mac602@00 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + read-only;
> + };
> +};
> +
> +&i2c2 {
> + tca9548@70 {
> + compatible = "nxp,pca9548";
> + pinctrl-0 = <&pinctrl_i2c_mux_reset>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x70>;
> + reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
> +
> + i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + sfp2: at24c04@50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + };
> + };
> +
> + i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> +
> + sfp3: at24c04@50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + };
> + };
> +
> + i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +&gpio0 {
> + eth0_intrp {
> + gpio-hog;
> + gpios = <23 GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "sx1503-irq";
> + };
> +};
> +
> +&gpio3 {
> + eth0_intrp {
> + gpio-hog;
> + gpios = <2 GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "eth0-intrp";
> + };
> +};
> +
> +&fec0 {
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec0_phy_int>;
> +
> + interrupt-parent = <&gpio3>;
> + interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> + reg = <0>;
> + };
> + };
> +};
> +
> +&iomuxc {
> + pinctr_atzb_rf_233: pinctrl-atzb-rf-233 {
> + fsl,pins = <
> + VF610_PAD_PTB2__GPIO_24 0x31c2
> + VF610_PAD_PTE27__GPIO_132 0x33e2
> + >;
> + };
> +
> +
> + pinctrl_sx1503_20: pinctrl-sx1503-20 {
> + fsl,pins = <
> + VF610_PAD_PTB1__GPIO_23 0x219d
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + VF610_PAD_PTA20__UART3_TX 0x21a2
> + VF610_PAD_PTA21__UART3_RX 0x21a1
> + >;
> + };
> +
> + pinctrl_mdio_mux: pinctrl-mdio-mux {
> + fsl,pins = <
> + VF610_PAD_PTA18__GPIO_8 0x31c2
> + VF610_PAD_PTA19__GPIO_9 0x31c2
> + VF610_PAD_PTB3__GPIO_25 0x31c2
> + >;
> + };
> +
> + pinctrl_fec0_phy_int: pinctrl-fec0-phy-int {
> + fsl,pins = <
> + VF610_PAD_PTB28__GPIO_98 0x219d
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/vf610-zii-dev.dtsi
> b/arch/arm/boot/dts/vf610-zii-dev.dtsi
> new file mode 100644
> index 0000000..9f5e2e7
> --- /dev/null
> +++ b/arch/arm/boot/dts/vf610-zii-dev.dtsi
> @@ -0,0 +1,383 @@
> +/*
> + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations
> + *
> + * Based on an original 'vf610-twr.dts' which is Copyright 2015,
> + * Freescale Semiconductor, Inc.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> +n * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "vf610.dtsi"
> +
> +/ {
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&pinctrl_leds_debug>;
> + pinctrl-names = "default";
> +
> + debug {
> + label = "zii:green:debug1";
> + gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_3v3_mcu";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + usb0_vbus: regulator-usb0-vbus {
> + compatible = "regulator-fixed";
> + pinctrl-0 = <&pinctrl_usb_vbus>;
> + regulator-name = "usb_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 6 0>;
> + };
> +};
> +
> +&adc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc0_ad5>;
> + vref-supply = <®_vcc_3v3_mcu>;
> + status = "okay";
> +};
> +
> +&edma0 {
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&fec0 {
> + phy-mode = "rmii";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec0>;
> + status = "okay";
> +};
> +
> +&fec1 {
> + phy-mode = "rmii";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + status = "okay";
> +
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> +
> + mdio1: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> + };
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c0>;
> + pinctrl-1 = <&pinctrl_i2c0_gpio>;
> + scl-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
> + sda-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + lm75@48 {
> + compatible = "national,lm75";
> + reg = <0x48>;
> + };
> +
> + at24c04@50 {
> + compatible = "atmel,24c04";
> + reg = <0x50>;
> + };
> +
> + at24c04@52 {
> + compatible = "atmel,24c04";
> + reg = <0x52>;
> + };
> +
> + ds1682@6b {
> + compatible = "dallas,ds1682";
> + reg = <0x6b>;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart0>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&usbdev0 {
> + disable-over-current;
> + vbus-supply = <&usb0_vbus>;
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbh1 {
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usbmisc0 {
> + status = "okay";
> +};
> +
> +&usbmisc1 {
> + status = "okay";
> +};
> +
> +&usbphy0 {
> + status = "okay";
> +};
> +
> +&usbphy1 {
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_adc0_ad5: adc0ad5grp {
> + fsl,pins = <
> + VF610_PAD_PTC30__ADC0_SE5 0x00a1
> + >;
> + };
> +
> + pinctrl_dspi0: dspi0grp {
> + fsl,pins = <
> + VF610_PAD_PTB18__DSPI0_CS1 0x1182
> + VF610_PAD_PTB19__DSPI0_CS0 0x1182
> + VF610_PAD_PTB20__DSPI0_SIN 0x1181
> + VF610_PAD_PTB21__DSPI0_SOUT 0x1182
> + VF610_PAD_PTB22__DSPI0_SCK 0x1182
> + >;
> + };
> +
> + pinctrl_dspi2: dspi2grp {
> + fsl,pins = <
> + VF610_PAD_PTD31__DSPI2_CS1 0x1182
> + VF610_PAD_PTD30__DSPI2_CS0 0x1182
> + VF610_PAD_PTD29__DSPI2_SIN 0x1181
> + VF610_PAD_PTD28__DSPI2_SOUT 0x1182
> + VF610_PAD_PTD27__DSPI2_SCK 0x1182
> + >;
> + };
> +
> + pinctrl_esdhc1: esdhc1grp {
> + fsl,pins = <
> + VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
> + VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
> + VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
> + VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
> + VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
> + VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
> + VF610_PAD_PTA7__GPIO_134 0x219d
> + >;
> + };
> +
> + pinctrl_fec0: fec0grp {
> + fsl,pins = <
> + VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d2
> + VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d3
> + VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1
> + VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1
> + VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1
> + VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1
> + VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2
> + VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2
> + VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + VF610_PAD_PTA6__RMII_CLKIN 0x30d1
> + VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2
> + VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
> + VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
> + VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
> + VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
> + VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
> + VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
> + VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
> + VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
> + >;
> + };
> +
> + pinctrl_gpio_spi0: pinctrl-gpio-spi0 {
> + fsl,pins = <
> + VF610_PAD_PTB22__GPIO_44 0x33e2
> + VF610_PAD_PTB21__GPIO_43 0x33e2
> + VF610_PAD_PTB20__GPIO_42 0x33e1
> + VF610_PAD_PTB19__GPIO_41 0x33e2
> + VF610_PAD_PTB18__GPIO_40 0x33e2
> + >;
> + };
> +
> + pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
> + fsl,pins = <
> + VF610_PAD_PTE14__GPIO_119 0x31c2
> + >;
> + };
> +
> + pinctrl_i2c0: i2c0grp {
> + fsl,pins = <
> + VF610_PAD_PTB14__I2C0_SCL 0x37ff
> + VF610_PAD_PTB15__I2C0_SDA 0x37ff
> + >;
> + };
> +
> + pinctrl_i2c0_gpio: i2c0grp-gpio {
> + fsl,pins = <
> + VF610_PAD_PTB14__GPIO_36 0x31c2
> + VF610_PAD_PTB15__GPIO_37 0x31c2
> + >;
> + };
> +
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + VF610_PAD_PTB16__I2C1_SCL 0x37ff
> + VF610_PAD_PTB17__I2C1_SDA 0x37ff
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + VF610_PAD_PTA22__I2C2_SCL 0x37ff
> + VF610_PAD_PTA23__I2C2_SDA 0x37ff
> + >;
> + };
> +
> + pinctrl_leds_debug: pinctrl-leds-debug {
> + fsl,pins = <
> + VF610_PAD_PTD20__GPIO_74 0x31c2
> + >;
> + };
> +
> + pinctrl_qspi0: qspi0grp {
> + fsl,pins = <
> + VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3
> + VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff
> + VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3
> + VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3
> + VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3
> + VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3
> + >;
> + };
> +
> + pinctrl_uart0: uart0grp {
> + fsl,pins = <
> + VF610_PAD_PTB10__UART0_TX 0x21a2
> + VF610_PAD_PTB11__UART0_RX 0x21a1
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + VF610_PAD_PTB23__UART1_TX 0x21a2
> + VF610_PAD_PTB24__UART1_RX 0x21a1
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + VF610_PAD_PTD0__UART2_TX 0x21a2
> + VF610_PAD_PTD1__UART2_RX 0x21a1
> + >;
> + };
> +
> + pinctrl_usb_vbus: pinctrl-usb-vbus {
> + fsl,pins = <
> + VF610_PAD_PTA16__GPIO_6 0x31c2
> + >;
> + };
> +
> + pinctrl_usb0_host: usb0-host-grp {
> + fsl,pins = <
> + VF610_PAD_PTD6__GPIO_85 0x0062
> + >;
> + };
> +};
> --
> 2.5.5
>
