On 347, 12 13, 2006 at 02:45:46PM +0000, Russell King wrote:
> Linus, Andrew,
>
> This patch adds initial support to 8250-pci for the Korenix Jetcard PCI
> serial cards. The JC12xx cards are standard RS232-based serial cards
> utilising the Oxford 16C950 device.
>
> The JC14xx are RS422/RS485-based cards, but in order for these to be
> supported natively, we will need additional tweaks to the 8250 layers
> so we can specify some values for the 950's registers. Hence, these
> two entries are commented out.
IIRC 16c950 just need two bits in ACR set properly. Will attached patch
do the trick ?
> Signed-off-by: Russell King <[EMAIL PROTECTED]>
>
> drivers/serial/8250_pci.c | 24 ++++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
> index 4d0ff8f..89c3f2c 100644
> --- a/drivers/serial/8250_pci.c
> +++ b/drivers/serial/8250_pci.c
> @@ -2239,6 +2239,30 @@ static struct pci_device_id serial_pci_t
> pbn_b0_bt_1_460800 },
>
> /*
> + * Korenix Jetcard F0/F1 cards (JC1204, JC1208, JC1404, JC1408).
> + * Cards are identified by their subsystem vendor IDs, which
> + * (in hex) match the model number.
> + *
> + * Note that JC140x are RS422/485 cards which require ox950
> + * ACR = 0x10, and as such are not currently fully supported.
> + */
> + { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0,
> + 0x1204, 0x0004, 0, 0,
> + pbn_b0_4_921600 },
> + { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0,
> + 0x1208, 0x0004, 0, 0,
> + pbn_b0_4_921600 },
> +/* { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0,
> + 0x1402, 0x0002, 0, 0,
> + pbn_b0_2_921600 }, */
> +/* { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0,
> + 0x1404, 0x0004, 0, 0,
> + pbn_b0_4_921600 }, */
> + { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF1,
> + 0x1208, 0x0004, 0, 0,
> + pbn_b0_4_921600 },
> +
> + /*
> * Dell Remote Access Card 4 - [EMAIL PROTECTED]
> */
> { PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RAC4,
--
Andrey Panin | Linux and UNIX system administrator
[EMAIL PROTECTED] | PGP key: wwwkeys.pgp.net
diff -urdpNX /usr/share/dontdiff -x Makefile
linux-2.6.19.vanilla/drivers/serial/8250.c linux-2.6.19/drivers/serial/8250.c
--- linux-2.6.19.vanilla/drivers/serial/8250.c 2006-12-19 20:18:26.000000000
+0300
+++ linux-2.6.19/drivers/serial/8250.c 2006-12-19 19:53:04.000000000 +0300
@@ -1548,7 +1548,7 @@ static int serial8250_startup(struct uar
if (up->port.type == PORT_16C950) {
/* Wake up and initialize UART */
- up->acr = 0;
+ up->acr = port->initial_acr;
serial_outp(up, UART_LCR, 0xBF);
serial_outp(up, UART_EFR, UART_EFR_ECB);
serial_outp(up, UART_IER, 0);
@@ -2599,6 +2599,7 @@ int serial8250_register_port(struct uart
uart->port.iotype = port->iotype;
uart->port.flags = port->flags | UPF_BOOT_AUTOCONF;
uart->port.mapbase = port->mapbase;
+ uart->port.initial_acr = port->initial_acr;
if (port->dev)
uart->port.dev = port->dev;
diff -urdpNX /usr/share/dontdiff -x Makefile
linux-2.6.19.vanilla/drivers/serial/8250.h linux-2.6.19/drivers/serial/8250.h
--- linux-2.6.19.vanilla/drivers/serial/8250.h 2006-12-19 20:44:12.000000000
+0300
+++ linux-2.6.19/drivers/serial/8250.h 2006-12-19 20:28:29.000000000 +0300
@@ -29,6 +29,8 @@ struct old_serial_port {
unsigned short iomem_reg_shift;
};
+#define initial_acr unused[0]
+
/*
* This replaces serial_uart_config in include/linux/serial.h
*/
