Hi Manu,
Thanks for the reply
Yes, indeed I tried over the weekend and by selecting the higher limitation by
ISEL register:
if (!lnbp21_attach(mantis->fe, &mantis->adapter, 0, 0x40)) {
My rotor now moves. Do you think it is better to use static current protection?
But unfortunately that is not the end of the story. The problem that I am
having now is that patched mythtv rewrites the limits in my rotor?! And the
weird thing is
it does in such a way that I had to take the motor apart to recalibrate it. It
looks like there are
hard limits in the rotor (Aston 1.2) firmware which are not the software limits
because trying to reset
them either from Linux side or from Windoz did not help. So I actually had to
take it apart to recalibrate
the motor inside the rotor. I do not think there is a problem with the rotor
itself because I have been using it for over 2 years with my other Twinhah 102g
card without any problems.
I also wrote a small command line program (using libsec) that will do only
rotor commands. With that
program I can do goto n, store, reset, soft limits. All there operations work
fine. Goto nn steps also
works somewhat even though it is not taking the specified number of steps
precisely. I am not sure why.
Getting back to my mythtv setup - I have a committed switch behind the rotor.
So the rotor command is followed by (with 15ms delay) the switch, tone burst
and then tunning commands. I turned on the verbose in mantis module and looked
what i2c reports. The diseqc sequence looks correct. The only thing I see is
that the fifo gets filled up by the end of the sequence so we have to wait for
a few cycles before sending the next byte. So now I am thinking could there be
any problems if the pause between writing the diseqc bytes is a bit longer
since we write byte, check if fifo is full and then write the next byte. What
do you think about that? I was thinking of trying to write the whole diseqc
command and then check fifo or even better first check fifo and then write the
command since we have 15ms between commands anyway.
On the side - switch works 50% of the times so I should look into that too. It
is a really good Spaun switch and even with 102g works flawlessly.
Thanks for the help!
Simeon
----- Original Message ----
From: Manu Abraham <[EMAIL PROTECTED]>
To: Simeon Simeonov <[EMAIL PROTECTED]>
Cc: [email protected]
Sent: Sunday, February 24, 2008 12:26:34 PM
Subject: Re: [linux-dvb] Help with Skystar HD2 (Twinhan VP-1041/Azurewave AD
SP400 rebadge)
Manu Abraham wrote:
> Simeon Simeonov wrote:
>> Hi Gernot,
>>
>> I can confirm that I have similar experience to yours.
>> By the way do you know if one can control from the soft side (register or
>> some other means)
>> the max current output for the card. I am having a problem when trying to
>> tune with a rotor.
>> On the Linux side the current seems to be capped at 300 mA as on the XP I
>> see it goes to
>> about 440 mA. I was still surprised that this card can supply less current
>> than the 102g but
>> we take what we get ...
Can you please try this change, whether it helps in your case ?
In mantis_dvb.c
line #251
if (!lnbp21_attach(mantis->fe, &mantis->adapter, 0, 0)) {
change it to
if (!lnbp21_attach(mantis->fe, &mantis->adapter, 0x80, 0x40)) {
and see whether it helps in improving your current limited situation.
according to the specification it should yield 500 - 650mA
A word of caution, make sure that the auxilliary power connector is
connected. Current drawn will be a bit much higher in this case,
additionally Static Current Limiting is used, hence additional dissipation,
which means more current drawn which might overload the PCI bus, hence
it would be nice to use the auxilliary power connector.
Regards,
Manu
____________________________________________________________________________________
Be a better friend, newshound, and
know-it-all with Yahoo! Mobile. Try it now.
http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
