This bug is awaiting verification that the linux-lowlatency- hwe-6.11/6.11.0-1007.7~24.04.1 kernel in -proposed solves the problem. Please test the kernel and update this bug with the results. If the problem is solved, change the tag 'verification-needed-noble-linux- lowlatency-hwe-6.11' to 'verification-done-noble-linux-lowlatency- hwe-6.11'. If the problem still exists, change the tag 'verification- needed-noble-linux-lowlatency-hwe-6.11' to 'verification-failed-noble- linux-lowlatency-hwe-6.11'.
If verification is not done by 5 working days from today, this fix will be dropped from the source code, and this bug will be closed. See https://wiki.ubuntu.com/Testing/EnableProposed for documentation how to enable and use -proposed. Thank you! ** Tags added: kernel-spammed-noble-linux-lowlatency-hwe-6.11-v2 verification-needed-noble-linux-lowlatency-hwe-6.11 -- You received this bug notification because you are a member of Kernel Packages, which is subscribed to linux in Ubuntu. https://bugs.launchpad.net/bugs/2071471 Title: [UBUNTU 24.04] IOMMU DMA mode changed in kernel config causes massive throughput degradation for PCI-related network workloads Status in Ubuntu on IBM z Systems: Fix Released Status in linux package in Ubuntu: Fix Released Status in linux source package in Noble: Fix Released Status in linux source package in Oracular: Fix Released Bug description: SRU Justification: [Impact] * With the introduction of c76c067e488c "s390/pci: Use dma-iommu layer" (upstream with since kernel v6.7-rc1) there was a move (on s390x only) to a different dma-iommu implementation. * And with 92bce97f0c34 "s390/pci: Fix reset of IOMMU software counters" (again upstream since 6.7(rc-1) the IOMMU_DEFAULT_DMA_LAZY kernel config option should now be set to 'yes' by default for s390x. * Since CONFIG_IOMMU_DEFAULT_DMA_STRICT and IOMMU_DEFAULT_DMA_LAZY are related to each other CONFIG_IOMMU_DEFAULT_DMA_STRICT needs to be set to "no" by default, which was upstream done by b2b97a62f055 "Revert "s390: update defconfigs"". * These changes are all upstream, but were not picked up by the Ubuntu kernel config. * And not having these config options set properly is causing significant PCI-related network throughput degradation (up to -72%). * This shows for almost all workloads and numbers of connections, deteriorating with the number of connections increasing. * Especially drastic is the drop for a high number of parallel connections (50 and 250) and for small and medium-size transactional workloads. However, also for streaming-type workloads the degradation is clearly visible (up to 48% degradation). [Fix] * The (upstream accepted) fix is to set IOMMU_DEFAULT_DMA_STRICT=no and IOMMU_DEFAULT_DMA_LAZY=y (which is needed for the changed DAM IOMMU implementation since v6.7). [Test Case] * Setup two Ubuntu Server 24.04 systems (with kernel 6.8) (one acting as server and as client) that have (PCIe attached) RoCE Express devices attached and that are connected to each other. * Verify if the the iommu_group type of the used PCI device is DMA-FQ: cat /sys/bus/pci/devices/<device>\:00\:00.0/iommu_group/type DMA-FQ * Sample workload rr1c-200x1000-250 with rr1c-200x1000-250.xml: <?xml version="1.0"?> <profile name="TCP_RR"> <group nprocs="250"> <transaction iterations="1"> <flowop type="connect" options="remotehost=<remote IP> protocol=tcp tcp_nodelay" /> </transaction> <transaction duration="300"> <flowop type="write" options="size=200"/> <flowop type="read" options="size=1000"/> </transaction> <transaction iterations="1"> <flowop type="disconnect" /> </transaction> </group> </profile> * Install uperf on both systems, client and server. * Start uperf at server: uperf -s * Start uperf at client: uperf -vai 5 -m uperf-profile.xml * Switch from strict to lazy mode either using the new kernel (or the test build below) or using kernel cmd-line parameter iommu.strict=0. * Restart uperf on server and client, like before. * Verification will be performed by IBM. [Regression Potential] * The is a certain regression potential, since the behavior with the two modified kernel config options will change significantly. * This may solve the (network) throughput issue with PCI devices, but may also come with side-effects on other PCIe based devices (the old compression adapters or the new NVMe carrier cards). [Other] * CCW devices are not affected. * This is s390x-specific only, hence will not affect any other architecture. __________ Symptom: Comparing Ubuntu 24.04 (kernelversion: 6.8.0-31-generic) against Ubuntu 22.04, all of our PCI-related network measurements on LPAR show massive throughput degradations (up to -72%). This shows for almost all workloads and numbers of connections, detereorating with the number of connections increasing. Especially drastic is the drop for a high number of parallel connections (50 and 250) and for small and medium-size transactional workloads. However, also for streaming-type workloads the degradation is clearly visible (up to 48% degradation). Problem: With kernel config setting CONFIG_IOMMU_DEFAULT_DMA_STRICT=y, IOMMU DMA mode changed from lazy to strict, causing these massive degradations. Behavior can also be changed with a kernel commandline parameter (iommu.strict) for easy verification. The issue is known and was quickly fixed upstream in December 2023, after being present for little less than two weeks. Upstream fix: https://github.com/torvalds/linux/commit/b2b97a62f055dd638f7f02087331a8380d8f139a Repro: rr1c-200x1000-250 with rr1c-200x1000-250.xml: <?xml version="1.0"?> <profile name="TCP_RR"> <group nprocs="250"> <transaction iterations="1"> <flowop type="connect" options="remotehost=<remote IP> protocol=tcp tcp_nodelay" /> </transaction> <transaction duration="300"> <flowop type="write" options="size=200"/> <flowop type="read" options="size=1000"/> </transaction> <transaction iterations="1"> <flowop type="disconnect" /> </transaction> </group> </profile> 0) Install uperf on both systems, client and server. 1) Start uperf at server: uperf -s 2) Start uperf at client: uperf -vai 5 -m uperf-profile.xml 3) Switch from strict to lazy mode using kernel commandline parameter iommu.strict=0. 4) Repeat steps 1) and 2). Example: For the following example, we chose the workload named above (rr1c-200x1000-250): iommu.strict=1 (strict): 233464.914 TPS iommu.strict=0 (lazy): 835123.193 TPS To manage notifications about this bug go to: https://bugs.launchpad.net/ubuntu-z-systems/+bug/2071471/+subscriptions -- Mailing list: https://launchpad.net/~kernel-packages Post to : kernel-packages@lists.launchpad.net Unsubscribe : https://launchpad.net/~kernel-packages More help : https://help.launchpad.net/ListHelp
