** Changed in: linux-raspi (Ubuntu)
Status: Confirmed => Invalid
--
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux-raspi in Ubuntu.
https://bugs.launchpad.net/bugs/1882930
Title:
focal/linux-raspi: Upstream raspberrypi patchset 2020-06-10
Status in linux-raspi package in Ubuntu:
Invalid
Status in linux-raspi source package in Focal:
In Progress
Bug description:
Upstream raspberrypi patchset 2020-06-10
Ported from the following raspberrypi branch:
rpi-5.4.y
from https://github.com/raspberrypi/linux.git
w1_therm: remove redundant assignments to variable ret
w1_therm: Free the correct variable
w1_therm: adding bulk read support to trigger multiple conversion on bus
w1_therm: adding alarm sysfs entry
w1_therm: optimizing temperature read timings
w1_therm: adding eeprom sysfs entry
w1_therm: adding resolution sysfs entry
w1_therm: adding ext_power sysfs entry
w1_therm: fix reset_select_slave during discovery
w1_therm: adding code comments and code reordering
overlays: Update upstream overlays after vc4-kms-v3d change
overlays: i2c-gpio: Avoid open-drain warnings
Revert "overlays: gpio-keys: Avoid open-drain warnings"
snd_bcm2835: disable HDMI audio when vc4 is used (#3640)
vc4: cec: Restore cec physical address on reconnect
staging: vchiq_arm: Use g_dma_dev for dma_unmap_sg
vc4: Set driver_name for card
configs: Add SND_SOC_MAX98357A=m
Add Micro Crystal RV-1805 to i2c-rtc overlays
media: bcm2835-isp: fix bytes per line calculations for some image formats
overlays: i2c-rtc-gpio: Fix trickle-resistor-ohms param
net: rtl8192cu: fix gcc misleading whitespace warning
overlays: Add spi0 overlay to support sc16is752
overlays: gpio-shutdown: Add information for Raspberry Pi 1 Model B rev 1
overlays: gpio-shutdown: Add information for SysV init / inittab
overlays: i2c-rtc: Fix trickle-resistor-ohms param
brcmfmac: BCM43436 needs dedicated firmware
configs: Build HWMON core into kernel
configs: Switch to upstream thermal sensor for RPi 4 - BCM2711_THERMAL
ARM: dts: bcm2711-rpi: Remove downstream thermal sensor node
Revert "thermal: brcmstb_thermal: Add BCM2838 support"
Revert "thermal: brcmstb_thermal: Correct SoC name"
ARM: configs: Build BCM2711 thermal as module
ARM: dts: bcm2711: Enable thermal
thermal: Add BCM2711 thermal driver
dt-bindings: Add Broadcom AVS RO thermal
media: bcm2835-unicam: change minimum number of vb2_queue buffers to 1
Revert "zswap: Uncross module parameter setting functions"
ARM: dts: Update for new VCHIQ BCM2711 DMA support
staging: vchiq_arm: Clean up 40-bit DMA support
media: i2c: imx477: Return correct result on sensor id verification
drm/vc4: Add FKMS as an acceptable node for dma ranges.
drm/vc4: Adopt the dma configuration from the HVS or V3D component
configs: Add ZSWAP=y, ZBUD=m, Z3FOLD=m
zswap: Defer zswap initialisation
zswap: Uncross module parameter setting functions
media: bcm2835-unicam: Retain packing information on G_FMT
Switch to snd_soc_dai_set_bclk_ratio
overlays: Fix audio parameter of vc4-kms-v3d
configs: Restore missing NF_TABLES settings
staging:vc04_services: bcm2835-camera: Request headers with I-frame
staging:vc04_services: bcm2835-codec: Avoid fragmenting buffers
staging:vc04_services: bcm2835-codec: Request headers with I-frame
staging: vc04_services: mmal-vchiq: Update parameters list
drm/vc4: Fix VIC usage with Broadcast RGB
sc16is7xx: Fix for hardware flow control
media: bcm2835-unicam: Always service interrupts
configs: Use the upstream cpufreq driver
configs: Include the firmware-clocks driver
ARM: dts: Enable firmware-clocks on all Pis
defconfig: Add CMA and system dma-heaps to the config
dma-heap: Make the symbol 'dma_heap_ioctl_cmds' static
dma-buf: fix resource leak on -ENOTTY error return path
dma-buf: heaps: Remove redundant heap identifier from system heap name
dma-buf: heaps: Use _IOCTL_ for userspace IOCTL identifier
kselftests: Add dma-heap test
dma-buf: heaps: Add CMA heap to dmabuf heaps
dma-buf: heaps: Add system heap to dmabuf heaps
dma-buf: heaps: Add heap helpers
dma-buf: Add dma-buf heaps framework
udmabuf: fix dma-buf cpu access
udmabuf: implement begin_cpu_access/end_cpu_access hooks
udmabuf: separate out creating/destroying scatter-table
udmabuf: add a pointer to the miscdevice in dma-buf private data
udmabuf: use cache_sgt_mapping option
udmabuf: Remove deleted map/unmap handlers.
configs: Add imx477 sensor driver to all Raspberry Pi defconfigs
media: i2c: imx477: Add support for adaptive frame control
media: i2c: Add driver for Sony IMX477 sensor
dtoverlays: Add IMX477 sensor overlay
dt-bindings: media: i2c: Add IMX477 CMOS sensor binding
raspberrypi: dts: Switch to discrete ALSA devices
overlays: Move "fixed-clock" nodes to the root
overlays: tc358743: Use intra-overlay fragments
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux-raspi/+bug/1882930/+subscriptions
--
Mailing list: https://launchpad.net/~kernel-packages
Post to : kernel-packages@lists.launchpad.net
Unsubscribe : https://launchpad.net/~kernel-packages
More help : https://help.launchpad.net/ListHelp
