On Mon, Nov 04, 2013 at 11:22:03PM +0200, Ville Syrjälä wrote:
> On Mon, Nov 04, 2013 at 12:54:24PM -0800, Jesse Barnes wrote:
> > On VLV/BYT, we can adjust the CDclk frequency up or down based on the
> > max pixel clock we need to drive. Lowering it can save power, while
> > raising it is necessary to support high resolution.
> >
> > Add a new callback in modeset_affected_pipes and a
> > modeset_global_resources function to perform this adjustment as
> > necessary.
> >
> > v2: use punit interface for 320 and 266 MHz CDclk adjustments (Ville)
> > v3: reset GMBUS dividers too, since we changed CDclk (Ville)
> > v4: jump to highest voltage when going to 400MHz CDclk (Jesse)
> > v5: drop duplicate define (Ville)
> > use shifts by 1 for fixed point (Ville)
> > drop new callback (Daniel)
> > v6: fixup adjusted_mode.clock -> adjusted_mode.crtc_clock again (Ville)
> > document Bunit reg access better (Ville)
> >
> > Signed-off-by: Jesse Barnes <[email protected]>
> > ---
> > drivers/gpu/drm/i915/i915_reg.h | 9 ++
> > drivers/gpu/drm/i915/intel_display.c | 179
> > +++++++++++++++++++++++++++++++++++
> > drivers/gpu/drm/i915/intel_i2c.c | 4 -
> > 3 files changed, 188 insertions(+), 4 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/i915_reg.h
> > b/drivers/gpu/drm/i915/i915_reg.h
> > index 737d8a3..d644d75 100644
> > --- a/drivers/gpu/drm/i915/i915_reg.h
> > +++ b/drivers/gpu/drm/i915/i915_reg.h
> > @@ -360,9 +360,17 @@
> > #define VLV_IOSF_DATA (VLV_DISPLAY_BASE +
> > 0x2104)
> > #define VLV_IOSF_ADDR (VLV_DISPLAY_BASE +
> > 0x2108)
> >
> > +/* See configdb bunit SB addr map */
> > +#define BUNIT_REG_BISOC 0x11
> > +
> > #define PUNIT_OPCODE_REG_READ 6
> > #define PUNIT_OPCODE_REG_WRITE 7
> >
> > +#define PUNIT_REG_DSPFREQ 0x36
> > +#define DSPFREQSTAT_SHIFT 30
> > +#define DSPFREQSTAT_MASK (0x3 << DSPFREQSTAT_SHIFT)
> > +#define DSPFREQGUAR_SHIFT 14
> > +#define DSPFREQGUAR_MASK (0x3 << DSPFREQGUAR_SHIFT)
> > #define PUNIT_REG_PWRGT_CTRL 0x60
> > #define PUNIT_REG_PWRGT_STATUS 0x61
> > #define PUNIT_CLK_GATE 1
> > @@ -425,6 +433,7 @@
> > #define DSI_PLL_N1_DIV_MASK (3 << 16)
> > #define DSI_PLL_M1_DIV_SHIFT 0
> > #define DSI_PLL_M1_DIV_MASK (0x1ff << 0)
> > +#define CCK_DISPLAY_CLOCK_CONTROL 0x6b
> >
> > /*
> > * DPIO - a special bus for various display related registers to hide
> > behind
> > diff --git a/drivers/gpu/drm/i915/intel_display.c
> > b/drivers/gpu/drm/i915/intel_display.c
> > index 606a594..ae83f01 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -3894,6 +3894,175 @@ static void i9xx_pfit_enable(struct intel_crtc
> > *crtc)
> > I915_WRITE(BCLRPAT(crtc->pipe), 0);
> > }
> >
> > +static int valleyview_get_vco(struct drm_i915_private *dev_priv)
> > +{
> > + int vco;
> > +
> > + switch (dev_priv->mem_freq) {
> > + default:
> > + case 800:
> > + vco = 800;
> > + break;
> > + case 1066:
> > + vco = 1600;
> > + break;
> > + case 1333:
> > + vco = 2000;
> > + break;
> > + }
> > +
> > + return vco;
> > +}
> > +
> > +/* Adjust CDclk dividers to allow high res or save power if possible */
> > +static void valleyview_set_cdclk(struct drm_device *dev, int cdclk)
> > +{
> > + struct drm_i915_private *dev_priv = dev->dev_private;
> > + u32 val, cmd;
> > +
> > + if (cdclk >= 320) /* jump to highest voltage for 400MHz too */
> > + cmd = 2;
> > + else if (cdclk == 266)
> > + cmd = 1;
> > + else
> > + cmd = 0;
> > +
> > + mutex_lock(&dev_priv->rps.hw_lock);
> > + val = vlv_punit_read(dev_priv, PUNIT_REG_DSPFREQ);
> > + val &= ~DSPFREQGUAR_MASK;
> > + val |= (cmd << DSPFREQGUAR_SHIFT);
> > + vlv_punit_write(dev_priv, PUNIT_REG_DSPFREQ, val);
> > + if (wait_for((vlv_punit_read(dev_priv, PUNIT_REG_DSPFREQ) &
> > + DSPFREQSTAT_MASK) == (cmd << DSPFREQSTAT_SHIFT),
> > + 50)) {
> > + DRM_ERROR("timed out waiting for CDclk change\n");
> > + }
> > + mutex_unlock(&dev_priv->rps.hw_lock);
> > +
> > + if (cdclk == 400) {
> > + u32 divider, vco;
> > +
> > + vco = valleyview_get_vco(dev_priv);
> > + divider = ((vco << 1) / cdclk) - 1;
> > +
> > + mutex_lock(&dev_priv->dpio_lock);
> > + /* adjust cdclk divider */
> > + val = vlv_cck_read(dev_priv, CCK_DISPLAY_CLOCK_CONTROL);
> > + val &= ~0xf;
> > + val |= divider;
> > + vlv_cck_write(dev_priv, CCK_DISPLAY_CLOCK_CONTROL, val);
> > + mutex_unlock(&dev_priv->dpio_lock);
> > + }
> > +
> > + mutex_lock(&dev_priv->dpio_lock);
> > + /* adjust self-refresh exit latency value */
> > + val = vlv_bunit_read(dev_priv, BUNIT_REG_BISOC);
> > + val &= ~0x7f;
> > +
> > + /*
> > + * For high bandwidth configs, we set a higher latency in the bunit
> > + * so that the core display fetch happens in time to avoid underruns.
> > + */
> > + if (cdclk == 400)
> > + val |= 4500 / 250; /* 4.5 usec */
> > + else
> > + val |= 3000 / 250; /* 3.0 usec */
> > + vlv_bunit_write(dev_priv, BUNIT_REG_BISOC, val);
> > + mutex_unlock(&dev_priv->dpio_lock);
> > +
> > + /* Since we changed the CDclk, we need to update the GMBUSFREQ too */
> > + intel_i2c_reset(dev);
> > +}
> > +
> > +static int valleyview_cur_cdclk(struct drm_i915_private *dev_priv)
> > +{
> > + int cur_cdclk, vco;
> > + int divider;
> > +
> > + vco = valleyview_get_vco(dev_priv);
> > +
> > + mutex_lock(&dev_priv->dpio_lock);
> > + divider = vlv_cck_read(dev_priv, CCK_DISPLAY_CLOCK_CONTROL);
> > + mutex_unlock(&dev_priv->dpio_lock);
> > +
> > + divider &= 0xf;
> > +
> > + cur_cdclk = (vco << 1) / (divider + 1);
> > +
> > + return cur_cdclk;
> > +}
> > +
> > +static int valleyview_calc_cdclk(struct drm_i915_private *dev_priv,
> > + int max_pixclk)
> > +{
> > + int cur_cdclk;
> > +
> > + cur_cdclk = valleyview_cur_cdclk(dev_priv);
> > +
> > + /*
> > + * Really only a few cases to deal with, as only 4 CDclks are supported:
> > + * 200MHz
> > + * 267MHz
> > + * 320MHz
> > + * 400MHz
> > + * So we check to see whether we're above 90% of the lower bin and
> > + * adjust if needed.
> > + */
> > + if (max_pixclk > 288000) {
> > + return 400;
> > + } else if (max_pixclk > 240000) {
> > + return 320;
> > + } else
> > + return 266;
> > + /* Looks like the 200MHz CDclk freq doesn't work on some configs */
> > +}
> > +
> > +static int intel_mode_max_pixclk(struct drm_i915_private *dev_priv)
> > +{
> > + struct drm_device *dev = dev_priv->dev;
> > + struct intel_crtc *intel_crtc;
> > + int max_pixclk = 0;
> > +
> > + list_for_each_entry(intel_crtc, &dev->mode_config.crtc_list,
> > + base.head) {
> > + if (!intel_crtc->base.enabled)
> > + continue;
> > +
> > + max_pixclk = max(max_pixclk,
> > + intel_crtc->config.adjusted_mode.crtc_clock);
> > + }
> > +
> > + return max_pixclk;
> > +}
> > +
> > +static void valleyview_modeset_global_pipes(struct drm_device *dev,
> > + unsigned *prepare_pipes)
> > +{
> > + struct drm_i915_private *dev_priv = dev->dev_private;
> > + struct intel_crtc *intel_crtc;
> > + int max_pixclk = intel_mode_max_pixclk(dev_priv);
> > + int cur_cdclk = valleyview_cur_cdclk(dev_priv);
> > +
> > + if (valleyview_calc_cdclk(dev_priv, max_pixclk) == cur_cdclk)
> > + return;
> > +
> > + list_for_each_entry(intel_crtc, &dev->mode_config.crtc_list,
> > + base.head)
> > + if (intel_crtc->base.enabled)
> > + *prepare_pipes |= (1 << intel_crtc->pipe);
> > +}
> > +
> >
>
>
> So now the problem is now that we have to calculate max_pixclk before
> intel_crtc->config has been update for modeset_pipes.
>
> If we make intel_mode_max_pixclk() and valleyview_modeset_global_pipes() like
> so:
>
> static int intel_mode_max_pixclk(struct drm_i915_private *dev_priv,
> unsigned int modeset_pipes,
> struct intel_crtc_config *pipe_config)
> {
> struct drm_device *dev = dev_priv->dev;
> struct intel_crtc *intel_crtc;
> int max_pixclk = 0;
>
> list_for_each_entry(intel_crtc, &dev->mode_config.crtc_list, base.head)
> {
> if (!intel_crtc->base.enabled)
> continue;
Hmm. After a second though, this enabled check is still wrong. But we
know that if the pipe is in modeset_pipes it will be enabled, so we
could move the enabled check to the second branch like so:
if (modeset_pipes & (1 << pipe))
max(pipe_config);
else if (crtc->enabled)
max(intel_crtc->config);
>
> if (modeset_pipes & (1 << intel_crtc_pipe))
> max_pixclk = max(max_pixclk,
> pipe_config->adjusted_mode.crtc_clock);
> else
> max_pixclk = max(max_pixclk,
> intel_crtc->config.adjusted_mode.crtc_clock);
> }
>
> return max_pixclk;
> }
>
> static void valleyview_modeset_global_pipes(struct drm_device *dev,
> unsigned *prepare_pipes,
> unsigned int modeset_pipes,
> struct intel_crtc_config
> *pipe_config)
> {
> struct drm_i915_private *dev_priv = dev->dev_private;
> struct intel_crtc *intel_crtc;
> int max_pixclk = intel_mode_max_pixclk(dev_priv, modeset_pipes,
> pipe_config);
> int cur_cdclk = valleyview_cur_cdclk(dev_priv);
>
> if (valleyview_calc_cdclk(dev_priv, max_pixclk) == cur_cdclk)
> return;
>
> list_for_each_entry(intel_crtc, &dev->mode_config.crtc_list,
> base.head)
> if (intel_crtc->base.enabled)
> *prepare_pipes |= (1 << intel_crtc->pipe);
> }
>
> And then we calculate it after the new pipe config has been computed like so:
>
> ...
> if (modeset_pipes) {
> pipe_config = intel_modeset_pipe_config(crtc, fb, mode);
> if (IS_ERR(pipe_config)) {
> ret = PTR_ERR(pipe_config);
> pipe_config = NULL;
>
> goto out;
> }
> intel_dump_pipe_config(to_intel_crtc(crtc), pipe_config,
> "[modeset]");
> }
>
> + if (IS_VALLEYVIEW(dev))
> + valleyview_modeset_global_pipes(dev, &prepare_pipes,
> modeset_pipes, pipe_config);
>
> for_each_intel_crtc_masked(dev, disable_pipes, intel_crtc)
> intel_crtc_disable(&intel_crtc->base);
> ...
>
>
> Then things should just work (tm).
>
> --
> Ville Syrjälä
> Intel OTC
--
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
