I am still waiting for the dmesg logs, Rodrigo :P
I am pretty sure that you would have picked up if there is a general
problem, wit the modeset or HDMI.
I just want to check what is following from the mode and monitor
combination during blankout:
- is the mode YCBCR420 ?
- is scrambling enabled ?
- does the monitor supports 4k@60 RGB (594Mhz) or its 4k@60 YCBCR420
(300Mhz)
- are we in 12 BPC deep color mode ?
- is this a CEA 4k@60 mode, or other one ?
Regards
Shashank
On 11/11/2017 5:34 AM, Rodrigo Vivi wrote:
On Fri, Nov 10, 2017 at 11:50:21PM +0000, Manasi Navare wrote:
Looks good.
But are these the only places that need change to support 2.0?
Dont we need any changes in voltage swing programming or DDI clocks?
not that I'm aware of... but that would explain the blank screens...
Manasi`
On Fri, Nov 10, 2017 at 02:26:26PM -0800, Rodrigo Vivi wrote:
Starting on GLK we support HDMI 2.0. So this patch only
extend the work Shashank has made to GLK to CNL.
Cc: Paulo Zanoni <[email protected]>
Cc: Shashank Sharma <[email protected]>
Cc: Manasi Navare <[email protected]>
Signed-off-by: Rodrigo Vivi <[email protected]>
---
drivers/gpu/drm/i915/intel_hdmi.c | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c
b/drivers/gpu/drm/i915/intel_hdmi.c
index 2d95db64cdf2..1b22b587e98c 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1235,7 +1235,7 @@ static int intel_hdmi_source_max_tmds_clock(struct
intel_encoder *encoder)
&dev_priv->vbt.ddi_port_info[encoder->port];
int max_tmds_clock;
- if (IS_GEMINILAKE(dev_priv))
+ if (IS_GEMINILAKE(dev_priv) || INTEL_GEN(dev_priv) >= 10)
max_tmds_clock = 594000;
else if (INTEL_GEN(dev_priv) >= 8 || IS_HASWELL(dev_priv))
max_tmds_clock = 300000;
@@ -1511,7 +1511,8 @@ bool intel_hdmi_compute_config(struct intel_encoder
*encoder,
pipe_config->lane_count = 4;
- if (scdc->scrambling.supported && IS_GEMINILAKE(dev_priv)) {
+ if (scdc->scrambling.supported && (IS_GEMINILAKE(dev_priv) ||
+ INTEL_GEN(dev_priv) >= 10) {
if (scdc->scrambling.low_rates)
pipe_config->hdmi_scrambling = true;
@@ -2033,7 +2034,7 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
connector->doublescan_allowed = 0;
connector->stereo_allowed = 1;
- if (IS_GEMINILAKE(dev_priv))
+ if (IS_GEMINILAKE(dev_priv) || INTEL_GEN(dev_priv) >= 10)
connector->ycbcr_420_allowed = true;
intel_hdmi->ddc_bus = intel_hdmi_ddc_pin(dev_priv, port);
--
2.13.6
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
