On Thu, Oct 12, 2017 at 12:55:39PM +0200, Maarten Lankhorst wrote:
> If the connected output is disabled before this test is run, then the test
> will fail because actual_brightness stays at 0 instead of the value
> of the desired brightness. Fix this by reading intel_backlight/device
> for the output name, and enable that output at start of this test.
>
> Changes since v1:
> - Enable the connected output, instead of enabling all outputs.
> Changes since v2:
> - Set a dummy fb, just in case.
> Changes since v3:
> - Use igt_output_get_plane_type, not get_plane.
>
> Sample failure:
> IGT-Version: 1.20-g01c550a27986 (x86_64) (Linux: 4.14.0-rc3-fbconhax+ x86_64)
> (pm_backlight:1203) CRITICAL: Test assertion failure function
> test_and_verify, file pm_backlight.c:111:
> (pm_backlight:1203) CRITICAL: Failed assertion: ({ typeof(0) _a = (0);
> typeof(val - tolerance) _b = (val - tolerance); _a > _b ? _a : _b; }) <=
> result
> (pm_backlight:1203) CRITICAL: error: 91200 > 0
>
> Signed-off-by: Maarten Lankhorst <[email protected]>
> ---
> tests/pm_backlight.c | 47 +++++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/tests/pm_backlight.c b/tests/pm_backlight.c
> index 8258d4e4c124..a695f90913fd 100644
> --- a/tests/pm_backlight.c
> +++ b/tests/pm_backlight.c
> @@ -155,13 +155,56 @@ igt_main
> {
> struct context context = {0};
> int old;
> + igt_display_t display;
> + struct igt_fb fb;
>
> igt_skip_on_simulation();
>
> igt_fixture {
> + enum pipe pipe;
> + igt_output_t *output;
> + bool found = false;
> + char full_name[32] = {};
> + char *name;
> + drmModeModeInfo *mode;
> + igt_plane_t *primary;
> +
> /* Get the max value and skip the whole test if sysfs interface
> not available */
> igt_skip_on(backlight_read(&old, "brightness"));
> igt_assert(backlight_read(&context.max, "max_brightness") > -1);
> +
> + /*
> + * Backlight tests requires the output to be enabled,
> + * try to enable all.
> + */
> + kmstest_set_vt_graphics_mode();
> + igt_display_init(&display, drm_open_driver(DRIVER_INTEL));
> +
> + /* should be ../../cardX-$output */
> + igt_assert_lt(12, readlink(BACKLIGHT_PATH "/device", full_name,
> sizeof(full_name) - 1));
> + name = basename(full_name);
> +
> + for_each_pipe_with_valid_output(&display, pipe, output) {
> + if (strcmp(name + 6, output->name))
This string magic isn't all that clear here. I think it would have been
cleaner to iterate all connected outputs and look for the backlight
under each. But I can't be bothered to care that much so
Reviewed-by: Ville Syrjälä <[email protected]>
> + continue;
> +
> + found = true;
> + break;
> + }
> +
> + igt_assert_f(found, "Could not map \"%s\" to output (%s?)\n",
> name, name + 6);
> +
> + igt_output_set_pipe(output, pipe);
> + mode = igt_output_get_mode(output);
> +
> + igt_create_pattern_fb(display.drm_fd,
> + mode->hdisplay, mode->vdisplay,
> + DRM_FORMAT_XRGB8888,
> + LOCAL_DRM_FORMAT_MOD_NONE, &fb);
> + primary = igt_output_get_plane_type(output,
> DRM_PLANE_TYPE_PRIMARY);
> + igt_plane_set_fb(primary, &fb);
> +
> + igt_display_commit2(&display, display.is_atomic ? COMMIT_ATOMIC
> : COMMIT_LEGACY);
> }
>
> igt_subtest("basic-brightness")
> @@ -174,5 +217,9 @@ igt_main
> igt_fixture {
> /* Restore old brightness */
> backlight_write(old, "brightness");
> +
> + igt_display_fini(&display);
> + igt_remove_fb(display.drm_fd, &fb);
> + close(display.drm_fd);
> }
> }
> --
> 2.14.1
>
> _______________________________________________
> Intel-gfx mailing list
> [email protected]
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
