Another question would be to know if i915 is the correct module for the Intel HD Graphics from a Clarkdale i3 proc?
Thanks XabiX ________________________________ De : Xavier de Almeida <[email protected]> À : [email protected] Envoyé le : Lun 31 mai 2010, 21h 08min 15s Objet : [Intel-gfx] Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33 Hello, It's my first post in such mailing list. My issue is that I can't configure my old LCD supporting 1080i (interlace mode) with my Clarkdale i3 (h57) HD Graphics. I see in the Xorg log such messages: (II) intel(0): Not using mode "1920x1080i" (interlace mode not supported) Therefore my 1st question is to know if interlace is supposed to work with these drivers? Then I'd like to know what I am missing in my xorg.conf in order to be able to set this display mode (and also when the TV is not connected or powered on). My issue is that the resolution "negotiated" is 1280x720_50.0 instead of 1920x1080i. Thanks XabiX lspci: 00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0042] (rev 12) Subsystem: Giga-byte Technology Device [1458:d000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 29 Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at ff00 [size=8] Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0500c Data: 41a9 Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a4] PCIe advanced features <?> Kernel driver in use: i915 Kernel modules: i915 My EDID: # EDID version 1 revision 3 Section "Monitor" # Block type: 2:0 3:fc Identifier "TSB-TV" VendorName "TSB" ModelName "TSB-TV" # Block type: 2:0 3:fc # Block type: 2:0 3:fd HorizSync 15-46 VertRefresh 49-61 # Max dot clock (video bandwidth) 80 MHz # DPMS capabilities: Active off:no Suspend:no Standby:no Mode "1920x540" # vfreq 50.044Hz, hfreq 28.125kHz DotClock 74.250000 HTimings 1920 1968 2012 2640 VTimings 540 542 547 562 Flags "Interlace" "+HSync" "+VSync" EndMode Mode "1280x720" # vfreq 50.000Hz, hfreq 37.500kHz DotClock 74.250000 HTimings 1280 1464 1504 1980 VTimings 720 725 730 750 Flags "+HSync" "+VSync" EndMode
_______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
