Hi together, I am trying to capy a DVD. Somewhere it does not work as I want it. What I did until now:
#mplayer dvd:// #dd if=/dev/cdrom of=~/folder/moviedvd.iso #mplayer -dvd-device ~/folder/moviedvd.iso dvd:// I do not have any problem playing the iso file this way. #du -m moviedvd.iso 8016 moviedvd.iso This results in the first dvd+r dl I try to burn. #cdrecord -dao -v -gracetime=3 -dev=/dev/cdrom1 ~/folder/moviedvd.iso For the output see below. I cannot see any error - is there one? When trying to play the dvd: #mplayer dvd:// a52: error at resampling xscreensaver-command: not active: idle timer reset. a52: CRC check failed! 0.279 ct: 0.000 1/ 1 ??% ??% ??,?% 0 0 51% a52: CRC check failed! a52: error at resampling a52: CRC check failed! 0.193 ct: 0.008 7/ 7 ??% ??% ??,?% 0 0 78% What I tried until now: #regionset /dev/cdrom1 regionset version 0.1 -- reads/sets region code on DVD drives Current Region Code settings: RPC Phase: II type: NONE vendor resets available: 4 user controlled changes resets available: 5 drive plays discs from region(s):, mask=0xFF Would you like to change the region setting of your drive? [y/n]:y Enter the new region number for your drive [1..8]:2 New mask: 0xFFFFFFFD, correct? [y/n]:y Region code set successfully! Trying to burn the dvd again has the same error when playing it. Does anyone have an idea what I can do to go on? Thanks Cdrecord-ProDVD-ProBD-Clone 2.01.01a34 (x86_64-unknown-linux-gnu) Copyright (C) 1995-2007 Jörg Schilling TOC Type: 1 = CD-ROM cdrecord: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.cdrecord: Cannot allocate memory. WARNING: Cannot do mlockall(2). cdrecord: WARNING: This causes a high risk for buffer underruns. cdrecord: Operation not permitted. WARNING: Cannot set RR-scheduler cdrecord: Permission denied. WARNING: Cannot set priority using setpriority(). cdrecord: WARNING: This causes a high risk for buffer underruns. scsidev: '/dev/cdrom1' devname: '/dev/cdrom1' scsibus: -2 target: -2 lun: -2 Warning: Open by 'devname' is unintentional and not supported. Linux sg driver version: 3.5.27 Using libscg version 'schily-0.9'. SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'LITE-ON ' Identifikation : 'DVDRW SOHW-1633S' Revision : 'BS0H' Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM. Current: DVD+R/DL Profile: DVD+R/DL (current) Profile: DVD+R Profile: DVD+RW Profile: DVD-RW sequential recording Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-3 DVD+R driver (mmc_dvdplusr). Driver flags : NO-CD DVD MMC-3 SWABAUDIO BURNFREE FORCESPEED Supported modes: PACKET SAO Drive buf size : 1373184 = 1341 KB FIFO size : 4194304 = 4096 KB Track 01: data 8007 MB Total size: 8007 MB = 4099846 sectors Current Secsize: 2048 Blocks total: 4173824 Blocks current: 4173824 Blocks remaining: 73978 cdrecord: Operation not permitted. WARNING: Cannot set RR-scheduler cdrecord: Permission denied. WARNING: Cannot set priority using setpriority(). cdrecord: WARNING: This causes a high risk for buffer underruns. Forcespeed is OFF. Starting to write CD/DVD/BD at speed 2 in real SAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. Starting new track at sector: 0 Track 01: 8007 of 8007 MB written (fifo 100%) [buf 99%] 2.5x. Track 01: Total bytes read/written: 8396484608/8396484608 (4099846 sectors). Writing time: 2529.078s Average write speed 2.4x. Min drive buffer fill was 35% Fixating... Fixating time: 60.082s cdrecord: fifo had 132254 puts and 132254 gets. cdrecord: fifo was 0 times empty and 123115 times full, min fill was 43%.
