Bob Sanders wrote:
> On Sun, 18 Jun 2006 14:13:44 -0400
> sean <[EMAIL PROTECTED]> wrote:
>
>> I am trying to get my recently built system to recognize my Adaptec
>> 29160 configured on the system.
>> I have SCSI built into the kernel, here is the dmesg statement,
>> SCSI subsystem initialized,
>
> Do you have SCSI Transport Attributes ---> Parallel SCSI (SPI) Transport
> Attributes
> turned on as either a module or loaded?
>
>> I can see my sata drive, which from what I read, scsi needs to be
>> working for sata access,
>
> SATA doesn't need specific attributes unless it's really a SAS interface.
>
>
>> but there is nothing in dmesg about my scsi
>> card coming to life, and so I cannot see my cd burner and iomega jaz
>> drive that hang off it.
>>
>
> Should only need, under SCSI devices support --> SCSI disk, SCSI CDROM,
> the previously mentioned parallel Transport, under low-level drivers -->
> Adaptec AIC7xxx (aka New driver), SATA support, and the SATA chipset driver.
> The rest is pretty much wasted space.
>
> Bob
> -
Thanks Bob,
Things are improving, but still not over the top yet.
As you can see below the dmesg shows things starting to light up...
I am able to see the scsi cdrw and the jaz drive.
Tried mounting the jaz drive but as expected it failed, the format of
the unit cartridge is UFS. But it at least saw it, assigned it, and
tried to mount when I manually tried.
However the scsi cdrw is still not working.
Again, as you can see it dmesg shows the device. However it is not
assigning it a dev.
The sr0 assignment you see listed is for my sata dvd unit, which is able
to mount when I tested it.
Are you, or anyone, able to offer any other suggestions?
Thanks
Sean
-----------------------------------------------------------------------
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: PLEXTOR Model: CD-R PX-W4012S Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
target0:0:1: Beginning Domain Validation
target0:0:1: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15)
target0:0:1: Domain Validation skipping write tests
target0:0:1: Ending Domain Validation
Vendor: iomega Model: jaz 1GB Rev: J.83
Type: Direct-Access ANSI SCSI revision: 02
target0:0:4: Beginning Domain Validation
target0:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
target0:0:4: Domain Validation skipping write tests
target0:0:4: Ending Domain Validation
libata version 1.20 loaded.
SCSI device sda: 2091050 512-byte hdwr sectors (1071 MB)
sda: Write Protect is off
sda: Mode Sense: 39 00 10 08
SCSI device sda: drive cache: write back w/ FUA
SCSI device sda: 2091050 512-byte hdwr sectors (1071 MB)
sda: Write Protect is off
sda: Mode Sense: 39 00 10 08
SCSI device sda: drive cache: write back w/ FUA
sda: sda1
sd 0:0:4:0: Attached scsi removable disk sda
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sr 0:0:1:0: Attached scsi CD-ROM sr0
sr 0:0:1:0: Attached scsi generic sg0 type 5
sd 0:0:4:0: Attached scsi generic sg1 type 0
--
[email protected] mailing list
