Well it works, thanks !!! On 2/13/06, Allan Spagnol Comar <[EMAIL PROTECTED]> wrote: > I will try change the file and I got in touch about what happens > > On 2/12/06, Harm Geerts <[EMAIL PROTECTED]> wrote: > > On Monday 13 February 2006 03:26, Allan Spagnol Comar wrote: > > > Hi all, > > > > > > I had installed lm_sensors and kernel modules, now when I run sensors > > > command I got: > > > > > > monstro ~ # sensors > > > it8712-isa-0290 > > > Adapter: ISA adapter > > > VCore 1: +1.41 V (min = +1.42 V, max = +1.57 V) ALARM > > > VCore 2: +0.00 V (min = +2.40 V, max = +2.61 V) ALARM > > > +3.3V: +6.53 V (min = +3.14 V, max = +3.46 V) ALARM > > > +5V: +5.00 V (min = +4.76 V, max = +5.24 V) > > > +12V: +11.84 V (min = +11.39 V, max = +12.61 V) > > > -12V: -4.17 V (min = -12.63 V, max = -11.41 V) ALARM > > > -5V: -13.64 V (min = -5.26 V, max = -4.77 V) ALARM > > > Stdby: +4.89 V (min = +4.76 V, max = +5.24 V) > > > VBat: +3.12 V > > > fan1: 0 RPM (min = 0 RPM, div = 8) > > > fan2: 0 RPM (min = 3013 RPM, div = 8) ALARM > > > fan3: 6750 RPM (min = 3013 RPM, div = 8) > > > M/B Temp: +35 C (low = +15 C, high = +40 C) sensor = thermistor > > > CPU Temp: +40 C (low = +15 C, high = +45 C) sensor = thermistor > > > Temp3: +27 C (low = +15 C, high = +45 C) sensor = thermistor > > > > > > how you all can see VCore2 is unavailable and -5 and -12 information > > > seems to be switched, > > > > > > does anyone had a clue about it, I am running on a nvidia4 base > > > motherboard. > > > > You'll need to change some settings in /etc/sensors.conf for your sensor > > chip. > > Your output seems a lot like mine with a default config so I'll paste the > > relevant part of my config, I have a Asus A8N SLI-Deluxe with a > > it8712-isa-0290. > > > > After you've modified /etc/sensors.conf you need to run `sensors -s` for the > > changes to take effect. You also need to run `sensors -s` after a reboot. > > Unless you use the sensors init.d script you can add that command > > to /etc/conf.d/local.start > > > > # cat /etc/sensors.conf > > > > chip "it87-*" "it8712-*" > > > > # Modified for Asus A8N SLI-Deluxe > > > > # Voltage monitors as advised in the It8705 data sheet > > > > label in0 "VCore 1" > > label in1 "VCore 2" > > label in2 "+3.3V" > > label in3 "+5V" > > label in4 "+12V" > > label in5 "-5V" > > label in6 "-12V" > > label in7 "Stdby" > > label in8 "VBat" > > > > # vid is not monitored by IT8705F > > # comment out if you have IT8712 > > ignore vid > > ignore in1 > > > > # Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems > > # to report the VCORE voltage approximately 0.05V higher than the board's > > # BIOS does. Although it doesn't make much sense physically, uncommenting > > # the next line should bring the readings in line with the BIOS' ones in > > # this case. > > # compute in0 -0.05+@ , @+0.05 > > > > # If 3.3V reads 2X too high (Soyo Dragon and Asus A7V8X-X, for example), > > # comment out following line. > > # compute in2 2*@ , @/2 > > # > > compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) > > compute in4 ((30/10) +1)*@ , @/((30/10) +1) > > # For this family of chips the negative voltage equation is different from > > # the lm78. The chip uses two external resistor for scaling but one is > > # tied to a positive reference voltage. See ITE8705/12 datasheet (SIS950 > > # data sheet is wrong) > > # Vs = (1 + Rin/Rf) * Vin - (Rin/Rf) * Vref. > > # Vref = 4.096 volts, Vin is voltage measured, Vs is actual voltage. > > > > # The next two are negative voltages (-12 and -5). > > # The following formulas must be used. Unfortunately the datasheet > > # does not give recommendations for Rin, Rf, but we can back into > > # them based on a nominal +2V input to the chip, together with a 4.096V > > Vref. > > # Formula: > > # actual V = (Vmeasured * (1 + Rin/Rf)) - (Vref * (Rin/Rf)) > > # For -12V input use Rin/Rf = 6.68 > > # For -5V input use Rin/Rf = 3.33 > > # Then you can convert the forumula to a standard form like: > > compute in5 (7.67 * @) - 27.36 , (@ + 27.36) / 7.67 > > compute in6 (4.33 * @) - 13.64 , (@ + 13.64) / 4.33 > > # > > # this much simpler version is reported to work for a > > # Elite Group K7S5A board > > # > > # compute in5 -(36/10)*@, -@/(36/10) > > # compute in6 -(56/10)*@, -@/(56/10) > > # > > compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1) > > > > set in0_min 1.4 * 0.95 > > set in0_max 1.4 * 1.05 > > set in1_min 2.4 > > set in1_max 2.6 > > set in2_min 3.3 * 0.95 > > set in2_max 3.3 * 1.05 > > set in3_min 5.0 * 0.95 > > set in3_max 5.0 * 1.05 > > set in4_min 12 * 0.95 > > set in4_max 12 * 1.05 > > set in5_max -5 * 0.95 > > set in5_min -5 * 1.05 > > set in6_max -12 * 0.95 > > set in6_min -12 * 1.05 > > set in7_min 5 * 0.95 > > set in7_max 5 * 1.05 > > #the chip does not support in8 min/max > > > > # Temperature > > # > > # Important - if your temperature readings are completely whacky > > # you probably need to change the sensor type. > > # Adujst and uncomment the appropriate lines below. > > # The old method (modprobe it87 temp_type=0xXX) is no longer supported. > > # > > # 2 = thermistor; 3 = thermal diode; 0 = unused > > # set sensor1 3 > > # set sensor2 3 > > # set sensor3 3 > > # If a given sensor isn't used, you will probably want to ignore it > > # (see ignore statement right below). > > > > label temp1 "CPU Temp" > > set temp1_over 50 > > set temp1_low 15 > > label temp2 "MB Temp" > > set temp2_over 45 > > set temp2_low 15 > > # ignore temp3 > > label temp3 "Temp3" > > set temp3_over 40 > > set temp3_low 15 > > > > # The A7V8X-X has temperatures inverted, and needs a conversion for > > # CPU temp. Thanks to Preben Randhol for the formula. > > # label temp1 "CPU Temp" > > # label temp2 "M/B Temp" > > # compute temp1 (-15.096+1.4893*@), (@+15.096)/1.4893 > > > > # The A7V600 also has temperatures inverted, and needs a different > > # conversion for CPU temp. Thanks to Dariusz Jaszkowski for the formula. > > # label temp1 "CPU Temp" > > # label temp2 "M/B Temp" > > # compute temp1 (@+128)/3, ([EMAIL PROTECTED]) > > > > # Fans > > set fan1_min 0 > > set fan2_min 3000 > > ignore fan2 > > ignore fan3 > > set fan3_min 3000 > > -- > > gentoo-user@gentoo.org mailing list > > > > > > > -- > An application asked: > "Requeires Windows 9x, NT4 or better", > so I´ve installed Linux >
-- An application asked: "Requeires Windows 9x, NT4 or better", so I´ve installed Linux -- gentoo-user@gentoo.org mailing list
