commit: d2ab72aa2a35a2b15153babda245406a3a0e3bfb Author: Michael Mair-Keimberger <m.mairkeimberger <AT> gmail <DOT> com> AuthorDate: Mon Dec 21 16:08:19 2020 +0000 Commit: Sam James <sam <AT> gentoo <DOT> org> CommitDate: Mon Dec 21 18:15:04 2020 +0000 URL: https://gitweb.gentoo.org/repo/gentoo.git/commit/?id=d2ab72aa
sys-boot/raspberrypi-firmware: remove unused files Package-Manager: Portage-3.0.12, Repoman-3.0.2 Signed-off-by: Michael Mair-Keimberger <m.mairkeimberger <AT> gmail.com> Closes: https://github.com/gentoo/gentoo/pull/18747 Signed-off-by: Sam James <sam <AT> gentoo.org> .../raspberrypi-firmware-0_p20130711-cmdline.txt | 1 - .../raspberrypi-firmware-0_p20130711-config.txt | 81 ---------------------- 2 files changed, 82 deletions(-) diff --git a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-cmdline.txt b/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-cmdline.txt deleted file mode 100644 index 39112a2dba6..00000000000 --- a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-cmdline.txt +++ /dev/null @@ -1 +0,0 @@ -ipv6.disable=0 selinux=0 plymouth.enable=0 smsc95xx.turbo_mode=N dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=noop rootwait diff --git a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-config.txt b/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-config.txt deleted file mode 100644 index 9401530925d..00000000000 --- a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-config.txt +++ /dev/null @@ -1,81 +0,0 @@ -#from archlinux arm sdcard image -# uncomment if you get no picture on HDMI for a default "safe" mode -#hdmi_safe=1 - -# uncomment this if your display has a black border of unused pixels visible -# and your display can output without overscan -#disable_overscan=1 - -# uncomment the following to adjust overscan. Use positive numbers if console -# goes off screen, and negative if there is too much border -#overscan_left=16 -#overscan_right=16 -#overscan_top=16 -#overscan_bottom=16 - -# uncomment to force a console size. By default it will be display's size minus -# overscan. -#framebuffer_width=1280 -#framebuffer_height=720 - -# uncomment if hdmi display is not detected and composite is being output -#hdmi_force_hotplug=1 - -# uncomment to force a specific HDMI mode (this will force VGA) -#hdmi_group=1 -#hdmi_mode=1 - -# uncomment to force a HDMI mode rather than DVI. This can make audio work in -# DMT (computer monitor) modes -#hdmi_drive=2 - -# uncomment to increase signal to HDMI, if you have interference, blanking, or -# no display -#config_hdmi_boost=4 - -# uncomment for composite PAL -#sdtv_mode=2 - -#uncomment to overclock the arm. 700 MHz is the default. -#arm_freq=800 - -# for more options see http://elinux.org/RPi_config.txt - -## Some over clocking settings, govenor already set to ondemand - -##None -#arm_freq=700 -#core_freq=250 -#sdram_freq=400 -#over_voltage=0 - -##Modest -#arm_freq=800 -#core_freq=300 -#sdram_freq=400 -#over_voltage=0 - -##Medium -#arm_freq=900 -#core_freq=333 -#sdram_freq=450 -#over_voltage=2 - -##High -#arm_freq=950 -#core_freq=450 -#sdram_freq=450 -#over_voltage=6 - -##Turbo -#arm_freq=1000 -#core_freq=500 -#sdram_freq=500 -#over_voltage=6 - -gpu_mem_512=316 -gpu_mem_256=128 -cma_lwm=16 -cma_hwm=32 -cma_offline_start=16 -
