Hi Michael, This is a bit of a puzzler. The IPMI spec has no definition for this error code for the "Get FRU Inventory Area Info" command.
> 10.100.212.11: IPMI Command Data: > 10.100.212.11: ------------------ > 10.100.212.11: [ 10h] = cmd[ 8b] > 10.100.212.11: [ 81h] = comp_code[ 8b] Similar FRU commands treat 0x81 as "busy" errors. ---- FRU device busy. The requested cannot be completed because the implementation of the logical FRU device is in a state where the FRU information is temporarily unavailable. This could be due to a condition such as a loss of arbitration if the FRU is implemented as a device on a shared bus." ---- So I am just guessing that's what the vendor meant with the 0x81 completion code. I'm just taking a guess, but maybe some device in the system is legitimately stuck sensor wise. If possible, a hard power reset could fix (i.e. pulling the plug optimally, but remote power control hard reset if you can't do that)? If not, we'll have to add a workaround in the code to handle this case and just say the FRU information isn't available for this device. Al On Thu, 2020-08-20 at 09:54 +0000, FRANK Michael wrote: > Hello, > > Trust everybody is OK and like to say thank you for this very good > software. It helps us every day to prevent hardware outages. > > I have the error "ipmi_sdr_cache_iterate: error returned in callback" > on a Lenovo x3650 M5 Server HW rev 9. Other M5s working well. > > The last section in debug before closing the session is below. This > has no meaning for me, and any help is much appreciated. > > 10.100.212.11: ===================================================== > 10.100.212.11: IPMI 2.0 Get FRU Inventory Area Info Response > 10.100.212.11: ===================================================== > 10.100.212.11: RMCP Header: > 10.100.212.11: ------------ > 10.100.212.11: [ 6h] = version[ 8b] > 10.100.212.11: [ 0h] = reserved[ 8b] > 10.100.212.11: [ FFh] = sequence_number[ 8b] > 10.100.212.11: [ 7h] = message_class.class[ 5b] > 10.100.212.11: [ 0h] = message_class.reserved[ 2b] > 10.100.212.11: [ 0h] = message_class.ack[ 1b] > 10.100.212.11: IPMI RMCPPLUS Session Header: > 10.100.212.11: ----------------------------- > 10.100.212.11: [ 6h] = authentication_type[ 4b] > 10.100.212.11: [ 0h] = reserved1[ 4b] > 10.100.212.11: [ 0h] = payload_type[ 6b] > 10.100.212.11: [ 1h] = payload_type.authenticated[ 1b] > 10.100.212.11: [ 1h] = payload_type.encrypted[ 1b] > 10.100.212.11: [ 638898C2h] = session_id[32b] > 10.100.212.11: [ B1h] = session_sequence_number[32b] > 10.100.212.11: [ 20h] = ipmi_payload_len[16b] > 10.100.212.11: IPMI RMCPPLUS Payload: > 10.100.212.11: ---------------------- > 10.100.212.11: [ BYTE ARRAY ... ] = confidentiality_header[16B] > 10.100.212.11: [ 38h 2Dh E7h A8h 52h 65h 91h 6Fh ] > 10.100.212.11: [ FCh A8h 2Bh CDh DBh B9h E2h 19h ] > 10.100.212.11: [ BYTE ARRAY ... ] = payload_data[ 8B] > 10.100.212.11: [ 81h 2Ch 53h 20h 84h 10h 81h CBh ] > 10.100.212.11: [ 707060504030201h] = confidentiality_trailer[64b] > 10.100.212.11: IPMI Message Header: > 10.100.212.11: -------------------- > 10.100.212.11: [ 81h] = rq_addr[ 8b] > 10.100.212.11: [ 0h] = rq_lun[ 2b] > 10.100.212.11: [ Bh] = net_fn[ 6b] > 10.100.212.11: [ 53h] = checksum1[ 8b] > 10.100.212.11: [ 20h] = rs_addr[ 8b] > 10.100.212.11: [ 0h] = rs_lun[ 2b] > 10.100.212.11: [ 21h] = rq_seq[ 6b] > 10.100.212.11: IPMI Command Data: > 10.100.212.11: ------------------ > 10.100.212.11: [ 10h] = cmd[ 8b] > 10.100.212.11: [ 81h] = comp_code[ 8b] > 10.100.212.11: IPMI Trailer: > 10.100.212.11: ------------- > 10.100.212.11: [ CBh] = checksum2[ 8b] > 10.100.212.11: IPMI RMCPPLUS Session Trailer: > 10.100.212.11: ------------------------------ > 10.100.212.11: [ FFFFh] = integrity_pad[16b] > 10.100.212.11: [ 2h] = pad_length[ 8b] > 10.100.212.11: [ 7h] = next_header[ 8b] > 10.100.212.11: [ BYTE ARRAY ... ] = authentication_code[12B] > 10.100.212.11: [ DEh 3Ah 51h DDh 19h F9h 9Bh 0Ch ] > 10.100.212.11: [ F5h 0Bh F2h 18h ] > ipmi_fru_open_device_id: internal IPMI error > ipmi_sdr_cache_iterate: error returned in callback > > > > Michael FRANK > Supervisor Global Monitoring Architecture Faurecia Clean Mobility T > +49 821 4103 420 ● M +49 171 9967 206 [email protected] > Faurecia Emissions Control Technologies, Germany GmbH - Biberbachstraße 9 – > 86154 Augsburg – Germany > > Sitz der Gesellschaft: Augsburg - Registergericht Augsburg HR B 20757 > Geschäftsführer: Yves Andres, Françoise Crenn, Thomas Hanak > Vorsitzender des Aufsichtsrats: Mathias Miedreich > > > > This electronic transmission (and any attachments thereto) is > intended solely for the use of the addressee(s). It may contain > confidential or legally privileged information. If you are not the > intended recipient of this message, you must delete it immediately > and notify the sender. Any unauthorized use or disclosure of this > message is strictly prohibited. Faurecia does not guarantee the > integrity of this transmission and shall therefore never be liable if > the message is altered or falsified nor for any virus, interception > or damage to your system. > WARNING: This email violated LLNL's email security policy and has > been > modified. If you would like a list of blocked file types or for more > information please see: > > https://www-csp.llnl.gov/security-ops-center/email-extension-blocks > > An attachment (ipmi.tgz) was removed from this document as it > constituted a security hazard. If you require this document, please > contact > the sender and arrange an alternate means of receiving it. > _______________________________________________ > Freeipmi-users mailing list > [email protected] > https://lists.gnu.org/mailman/listinfo/freeipmi-users _______________________________________________ Freeipmi-users mailing list [email protected] https://lists.gnu.org/mailman/listinfo/freeipmi-users
