Device ID : 36 Device Revision : 1 Device SDRs : unsupported Firmware Revision : 1.17 Device Available : yes (normal operation) IPMI Version : 2.0 Sensor Device : supported SDR Repository Device : supported SEL Device : supported FRU Inventory Device : supported IPMB Event Receiver : supported IPMB Event Generator : supported Bridge : unsupported Chassis Device : supported Manufacturer ID : INVENTEC CORPORATION (6569) Product ID : 54 Auxiliary Firmware Revision Information : 00000000h
GUID : 00000000-0000-0000-0000-000000000000 System Firmware Version : rsion1.0 System Name : Manager Primary Operating System Name : SE Server 1.0 Operating System Name : Channel Information Channel Number : 0 Medium Type : IPMB (I2C) Protocol Type : IPMB-1.0 Active Session Count : 0 Session Support : session-less Vendor ID : Intelligent Platform Management Interface forum (7154) Channel Number : 1 Medium Type : 802.3 LAN Protocol Type : IPMB-1.0 Active Session Count : 0 Session Support : multi-session Vendor ID : Intelligent Platform Management Interface forum (7154) Channel Number : 6 Medium Type : IPMB (I2C) Protocol Type : IPMB-1.0 Active Session Count : 0 Session Support : session-less Vendor ID : Intelligent Platform Management Interface forum (7154) Channel Number : 7 Medium Type : System Interface (KCS, SMIC, or BT) Protocol Type : KCS Active Session Count : 0 Session Support : session-less Vendor ID : Intelligent Platform Management Interface forum (7154) On Mon, Jan 23, 2017 at 1:30 PM, Albert Chu <[email protected]> wrote: > Hi, > > What are the other channel numbers (could you show via the output of > bmc-info)? > > Also, could you elaborate on your use case scenario? > > Thanks, > > Al > > On Mon, 2017-01-23 at 13:18 -0800, VJ wrote: > > I only see > > 1) Lan_Channel > > 2) Serial_Channel > > > > > > there are 16 channels and they are not displayed even with -v > > > > On Thu, Jan 19, 2017 at 11:51 AM, Albert Chu <[email protected]> wrote: > > Hi, > > > > Do you wish to disable a very specific channel number, so you > > wish to be > > able to enable/disable based on the input of a number? At the > > moment > > that isn't supported. Could you elaborate on your use case > > scenario? > > > > Other channels are configurable in bmc-config if you specify > > --verbose > > when you checkout. If there are multiple lan channels you can > > configure > > both, other less common channels like serial are also output > > for > > configuration. > > > > Al > > > > On Thu, 2017-01-19 at 11:37 -0800, VJ wrote: > > > Hi > > > > > > Can I disable a channel using bmc-config configuration ? > > > I dont see the sections disabling or enabling other than lan > > channel. > > > I looked at bmc-config man page and it doesnt mention it. > > > > > > Thanks. > > > > > _______________________________________________ > > > Freeipmi-users mailing list > > > [email protected] > > > https://lists.gnu.org/mailman/listinfo/freeipmi-users > > > > -- > > Albert Chu > > [email protected] > > Computer Scientist > > High Performance Systems Division > > Lawrence Livermore National Laboratory > > > > > > > > > > > > > > -- > > ------------------------------------------------------------ > --------------------------- > > ** Believe in : Hardwork Science God** > > ============================================ > > > > -- > Albert Chu > [email protected] > Computer Scientist > High Performance Systems Division > Lawrence Livermore National Laboratory > > > -- --------------------------------------------------------------------------------------- ** Believe in : Hardwork Science God** ============================================ _______________________________________________ Freeipmi-users mailing list [email protected] https://lists.gnu.org/mailman/listinfo/freeipmi-users
