On 03/14/12 19:40, YongHyeon PYUN wrote:
On Tue, Mar 13, 2012 at 02:08:46PM +0100, Jan Winter wrote:
Hello,
on an Dell Blade m610 is not possible to change the network media option:
ifconfig bce0 media 100baseTX mediaopt full-duplex up
ifconfig: SIOCSIFMEDIA (media): Device not configured
Setting the media option to "autoselect" and connecting the m610 to a
100 MBit switch, I always get "no carrier"
only 1g full-duplex seems to be working. I have tested this on
8.3-prerelease and 9-stable
any Ideas?
cheers
Jan
pciconf -lv
bce0@pci0:1:0:0: class=0x020000 card=0x02871028 chip=0x163a14e4
rev=0x20 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'NetXtreme II BCM5709S Gigabit Ethernet'
class = network
subclass = ethernet
dmesg
bce0:<Broadcom NetXtreme II BCM5709 1000Base-SX (C0)> mem
0xda000000-0xdbffffff irq 36 at device 0.0 on pci1
miibus0:<MII bus> on bce0
brgphy0:<BCM5709S 1000/2500baseSX PHY> PHY 2 on miibus0
brgphy0: 1000baseSX-FDX, auto
bce0: Ethernet address: 00:26:b9:fb:04:0c
bce0: ASIC (0x57092000); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.0.11);
Bufs (RX:2;TX:2;PG:8); Flags (SPLT|MSI|MFW); MFW (NCSI 2.0.5)
Coal (RX:6,6,18,18; TX:20,20,80,80)
bce1:<Broadcom NetXtreme II BCM5709 1000Base-SX (C0)> mem
0xdc000000-0xddffffff irq 48 at device 0.1 on pci1
miibus1:<MII bus> on bce1
brgphy1:<BCM5709S 1000/2500baseSX PHY> PHY 2 on miibus1
brgphy1: 1000baseSX-FDX, auto
bce1: Ethernet address: 00:26:b9:fb:04:0e
bce1: ASIC (0x57092000); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.0.11);
Bufs (RX:2;TX:2;PG:8); Flags (SPLT|MSI|MFW); MFW (NCSI 2.0.5)
Coal (RX:6,6,18,18; TX:20,20,80,80)
I'm not sure you're seeing one of long standing remote PHY issue of
blade box but would you try the patch at the following URL?
http://people.freebsd.org/~yongari/bce/bce.rphy.diff
After applying the patch, show me the dmesg output(bce(4) and
brgphy(4) related ones) and 'ifconfig -m bce0'.
Note, the patch was not tested at all(lack of hardware).
Hello,
thank you very much, for your quick support
Now its looking much better
ifconfig -m bce0
bce0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
capabilities=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
ether 00:26:b9:fb:04:0c
inet 192.168.100.30 netmask 0xffffff00 broadcast 192.168.100.255
inet6 fe80::226:b9ff:fefb:40c%bce0 prefixlen 64 tentative
scopeid 0x1
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (1000baseT<full-duplex>)
status: active
supported media:
media autoselect
media 1000baseT mediaopt full-duplex
media 1000baseT
media 100baseTX mediaopt full-duplex
media 100baseTX
media 10baseT/UTP mediaopt full-duplex
media 10baseT/UTP
dmesg:
.....
bce0:<Broadcom NetXtreme II BCM5709 1000Base-SX (C0)> mem
0xda000000-0xdbffffff irq 36 at device 0.0 on pci1
bce0: attempting to allocate 1 MSI vectors (16 supported)
msi: routing MSI IRQ 256 to local APIC 16 vector 52
bce0: using IRQ 256 for MSI
bce0: Remote PHY : TP
bce0: bpf attached
bce0: Ethernet address: 00:26:b9:fb:04:0c
bce0: ASIC (0x57092000); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.0.11);
Bufs (RX:2;TX:2;PG:8); Flags (SPLT|MSI|Remote PHY(TP)|MFW); MFW (NCSI 2.0.5)
Coal (RX:6,6,18,18; TX:20,20,80,80)
bce1:<Broadcom NetXtreme II BCM5709 1000Base-SX (C0)> mem
0xdc000000-0xddffffff irq 48 at device 0.1 on pci1
bce1: attempting to allocate 1 MSI vectors (16 supported)
msi: routing MSI IRQ 257 to local APIC 16 vector 53
bce1: using IRQ 257 for MSI
bce1: Remote PHY : TP
bce1: bpf attached
bce1: Ethernet address: 00:26:b9:fb:04:0e
bce1: ASIC (0x57092000); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.0.11);
Bufs (RX:2;TX:2;PG:8); Flags (SPLT|MSI|Remote PHY(TP)|MFW); MFW (NCSI 2.0.5)
Coal (RX:6,6,18,18; TX:20,20,80,80)
.....
I have done a quick test with 100 and 1000 MBit, both working very well.
