On 4/1/10 8:35 PM, Randy Bush wrote:
i have a year old 8 soekris system i am about to upgrade. it is pppoe
externally, and has a bridged natted wireless/ether internal net.
.----------------.
| |
| b --wlan0|
| r | 192.168.0.0/24
ext iij | i --- vr1| LAN hosts,
PPP/NAT ---|vr0--- d | DHCP Clients
WAN | g --- vr2| ...
| e |
| 0 --- vr3|
| |
`----------------'
ok this is similar to my setup in some ways.
but the picture is wrong,
remember that vr0 is not (or at least should not be) part of the bridge.
the real picture is:
> .----------------------------------.
> | |
> | b --wlan0|
> | r | 192.168.0.0/24
> ext iij | i --- vr1| LAN hosts,
> PPP/NAT ---|vr0[PPPoE][ppp]tun0--[R]-d | DHCP Clients
> WAN | g --- vr2| ...
> | e |
> | 0 --- vr3|
> | |
> `----------------------------------'
where [R] is the IP forwarding code (i.e routing not bridging)
/etc/rc.conf
ppp_enable=YES
ppp_mode=dedicated
ppp_nat=YES
ppp_profile=iij
my profile is pppoe which is shown below
It's not completely different from yours but seems to work
hostapd_enable=YES
wlans_ath0=wlan0
create_args_wlan0="wlanmode ap mode 11g channel 11 up"
cloned_interfaces=bridge0
ifconfig_bridge0="192.168.0.1 addm vr1 addm vr2 addm vr3 addm wlan0 addm wlan1
up"
I can't help you withthe bridge part but it should be ok I think.
ifconfig_vr1=up
ifconfig_vr2=up
ifconfig_vr3=up
/etc/hostap.conf
interface=wlan0
ctrl_interface=/var/run/hostapd
logger_syslog=-1
logger_syslog_level=0
ssid=rgnet-crypt
country_code=JP
hw_mode=g
wpa=2
wpa_key_mgmt=WPA-PSK
wpa_passphrase=notreally
wpa_pairwise=CCMP TKIP
/etc/ppp/ppp.conf entry
iij:
set device PPPoE:vr0
set MRU 1454 # NTT suggests this value
set MTU 1454
accept CHAP
enable lqr
add default HISADDR
nat enable yes
set authname nope
set authkey peon
pppoe:
set device PPPoE:vr1
set redial 10.3 10000
set speed 115200 #not really intersting
set timeout 0 # Never time out
disable dns
disable ipv6cp
disable sroutes
set authname heyitsme
set authkey really?
set login
enable lqr
set ifaddr X.X.X.X/32 0.0.0.0/0 255.255.255.255 0.0.0.0
add default HISADDR # Add a (sticky) default route
set cd 5
is this still gonna work? is this a reasonable way to do this? i ask
because, if it does not, i will not have usable connectivity to get help
fixing it :)
randy
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"
