> > > The following is the output of usbdevs -v
> > >
> > > # usbdevs -v
> > > Controller /dev/usb0:
> > > addr 1: self powered, config 1, UHCI root hub(0x0000), VIA(0x0000),
rev
> > > 0x0100
> > > port 1 powered
> > > port 2 powered
> >
> > This is with the "mouse" attached?
> >
> > If it doesn't even show up, that would point towards faulty hardware...
> >
>
> The mouse has already attached when execute usbdevs and I can use this
mouse
> in both Windows and Linux without any problem.
>
> With reference with the dmesg output attached, I guess the mouse is
attached
> in usb1 but I cannot confirm if it is true since I am only a newbie.
> However, the usbdevs only list /dev/usb0 but no usb1. I found there is no
> device usb1 in /dev so I tried to create the device node usb1 but usbdevs
> still only list /dev/usb0 but no usb1.
>
Sorry, usbdevs has shown usb1 after I have create the device node usb1. the
following is the output of usbdevs.
# usbdevs -v
Controller /dev/usb0:
addr 1: self powered, config 1, UHCI root hub(0x0000), VIA(0x0000), rev
0x0100
port 1 powered
port 2 powered
Controller /dev/usb1:
addr 1: self powered, config 1, UHCI root hub(0x0000), VIA(0x0000), rev
0x0100
port 1 powered
Dec 30 19:47:44 /kernel: uhci_device_request: not done, ii=0xc104f680
Dec 30 19:47:44 /kernel: uhci_device_request: not done, ii=0xc104f680
Dec 30 19:47:49 /kernel: uhci_timeout: ii=0xc104f680
Dec 30 19:47:49 /kernel: uhci_timeout: ii=0xc104f680
Dec 30 19:47:49 /kernel: uhci_device_request: not done, ii=0xc104f680
Dec 30 19:47:49 /kernel: uhci_device_request: not done, ii=0xc104f680
port 2 addr 2: self powered, config 1, product 0x9254(0x9254), Alcor Micro,
Inc.(0x058f), rev 0x0100
port 1 powered
Dec 30 19:47:54 /kernel: uhci_timeout: ii=0xc104f680
Dec 30 19:47:54 /kernel: uhci_timeout: ii=0xc104f680
Dec 30 19:47:54 /kernel: uhci_device_request: not done, ii=0xc104f600
Dec 30 19:47:54 /kernel: uhci_device_request: not done, ii=0xc104f600
Dec 30 19:47:59 /kernel: uhci_timeout: ii=0xc104f600
Dec 30 19:47:59 /kernel: uhci_timeout: ii=0xc104f600
Dec 30 19:47:59 /kernel: uhci_device_request: not done, ii=0xc104f600
Dec 30 19:47:59 /kernel: uhci_device_request: not done, ii=0xc104f600
port 2 addr 3: low speed, power 500 mA, config 1, iFeel Mouse(0xc030),
Logitech, Inc.(0x046d), rev 0x0101
port 3 disabled
port 4 disabled
# Dec 30 19:48:04 /kernel: uhci_timeout: ii=0xc104f600
Dec 30 19:48:04 /kernel: uhci_timeout: ii=0xc104f600
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-PRERELEASE #0: Sun Dec 23 01:55:47 HKT 2001
root@:/usr/obj/usr/src/sys/STABLE_DEBUG
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD Athlon(tm) Processor (1109.89-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x642 Stepping = 2
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
AMD Features=0xc0440000<<b18>,AMIE,DSP,3DNow!>
real memory = 536788992 (524208K bytes)
avail memory = 518246400 (506100K bytes)
Preloaded elf kernel "kernel" at 0xc0389000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 9 entries at 0xc00f1750
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <VIA 8363 (Apollo KT133) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <NVidia model 0110 graphics accelerator> at 0.0 irq 11
isab0: <VIA 82C686 PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA66 controller> port 0xd800-0xd80f at device 4.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 9 at device 4.2 on pci0
uhci0: LegSup = 0x0000003b
uhci_run: setting run=0
uhci_run: done cmd=0x80 sts=0x20
uhci_run: setting run=1
uhci_run: done cmd=0x81 sts=0x0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 9 at device 4.3 on pci0
uhci1: LegSup = 0x00000010
uhci_run: setting run=0
uhci_run: done cmd=0x80 sts=0x20
uhci_run: setting run=1
uhci_run: done cmd=0x81 sts=0x0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci_device_request: not done, ii=0xc104f680
uhub2: ALCOR Generic USB Hub, class 9/0, rev 1.10/1.00, addr 2
uhub2: 4 ports with 4 removable, self powered
uhci_device_intr_transfer: not done, ii=0xc104f620
uhci_waitintr: timeout
uhci_idone: error, addr=3, endpt=0x00, status 0x500000<BABBLE,STALLED>
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<1
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<1
ums0: Logitech, Inc. iFeel Mouse, rev 1.00/1.01, addr 3, iclass 3/1
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<74
device_probe_and_attach: ums0 attach returned 6
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<1
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<1
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<4
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<4
chip1: <VIA 82C686 ACPI interface> at device 4.4 on pci0
rl0: <RealTek 8139 10/100BaseTX> port 0xa400-0xa4ff mem 0xd5800000-0xd58000ff irq 9 at
device 9.0 on pci0
rl0: Ethernet address: 00:50:ff:60:0b:b8
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcm0: <Creative EMU10K1> port 0xa000-0xa01f irq 5 at device 10.0 on pci0
pci0: <unknown card> (vendor=0x104c, dev=0x8020) at 13.0 irq 9
atapci1: <Promise ATA100 controller> port
0x8000-0x803f,0x8400-0x8403,0x8800-0x8807,0x9000-0x9003,0x9400-0x9407 mem
0xd4000000-0xd401ffff irq 10 at device 17.0 on pci0
ata2: at 0x9400 on atapci1
ata3: at 0x8800 on atapci1
orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xcffff,0xd0000-0xd27ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
ad4: 43979MB <IBM-DTLA-307045> [89355/16/63] at ata2-master UDMA100
ad6: 57241MB <ST360021A> [116301/16/63] at ata3-master UDMA100
acd0: DVD-ROM <MATSHITADVD-ROM SR-8586> at ata0-master using PIO4
acd1: CD-RW <PLEXTOR CD-R PX-W1610A> at ata1-master using PIO4
Mounting root from ufs:/dev/ad4s2a
