Re: 13.3 14.x panic in qlogic isp vm_fault_lookup: fault on nofault entry, addr: 0xfffffe0127d22000

[Roger Hammerstein]

 

> Subject: 13.3 14.x panic in qlogic isp vm_fault_lookup: fault on nofault entry, addr: 0xfffffe0127d22000
> 13.2 works.   13.3 and 14.x panic.
 

 
13.3 iso will work if load ispfw first (escape to loader, unload kernel, load ispfw, load kernel, boot)

also,
adding            ispfw_load="YES"    to loader.conf
to the working 13.2-system, and then freebsd-update to 13.3 will also work.

 

 

the working 13.2 :

grep ^isp 13.2-dmesg

isp0: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x6c00-0x6cff mem 0xfc4fc000-0xfc4fffff irq 16 at device 0.0 on pci3
isp0: Mailbox Command (0x8) Timeout (5000000us) (isp_reset:439)
isp0: Mailbox Command 'ABOUT FIRMWARE' failed (TIMEOUT)
isp0: isp_reinit: cannot reset card
isp0: See the ispfw(4) man page on how to load known good firmware at boot time
isp0: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x9c00-0x9cff mem 0xfcbfc000-0xfcbfffff irq 18 at device 0.0 on pci9
isp0: Mailbox Command (0x8) Timeout (5000000us) (isp_reset:439)
isp0: Mailbox Command 'ABOUT FIRMWARE' failed (TIMEOUT)
isp0: isp_reinit: cannot reset card
isp0: See the ispfw(4) man page on how to load known good firmware at boot time
isp0: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x6c00-0x6cff mem 0xfc4fc000-0xfc4fffff irq 16 at device 0.0 on pci3
isp_2400: could not load firmware image, error 6
isp0: Mailbox Command (0x8) Timeout (5000000us) (isp_reset:439)
isp0: Mailbox Command 'ABOUT FIRMWARE' failed (TIMEOUT)
isp0: isp_reinit: cannot reset card
isp0: See the ispfw(4) man page on how to load known good firmware at boot time
isp0: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x9c00-0x9cff mem 0xfcbfc000-0xfcbfffff irq 18 at device 0.0 on pci9
isp_2400: could not load firmware image, error 6
isp0: Mailbox Command (0x8) Timeout (5000000us) (isp_reset:439)
isp0: Mailbox Command 'ABOUT FIRMWARE' failed (TIMEOUT)
isp0: isp_reinit: cannot reset card
isp0: See the ispfw(4) man page on how to load known good firmware at boot time
isp0: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x6c00-0x6cff mem 0xfc4fc000-0xfc4fffff irq 16 at device 0.0 on pci3
isp1: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x9c00-0x9cff mem 0xfcbfc000-0xfcbfffff irq 18 at device 0.0 on pci9

 

 

 

working 13.3 dmesg with ispfw loaded in loader.conf

 

grep ^isp 13.3-dmesg

 

isp0: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x6c00-0x6cff mem 0xfc4fc000-0xfc4fffff irq 16 at device 0.0 on pci3
isp0: FLT[DEF]: Invalid length=0xffff(65535)
isp0: invalid NVRAM header (55 aa 56)
isp0: invalid NVRAM header (55 aa 56)
isp0: bad frame length (0) from NVRAM - using 1024
isp1: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x9c00-0x9cff mem 0xfcbfc000-0xfcbfffff irq 18 at device 0.0 on pci9
isp1: FLT[DEF]: Invalid length=0xffff(65535)
isp1: invalid NVRAM header (55 aa 56)
isp1: invalid NVRAM header (55 aa 56)
isp1: bad frame length (0) from NVRAM - using 1024

 

 

 

 

 

 

Sent: Tuesday, July 16, 2024 at 6:27 PM
From: "Roger Hammerstein" <cheek...@gmx.com>
To: curr...@freebsd.org
Subject: 13.3 14.x panic in qlogic isp vm_fault_lookup: fault on nofault entry, addr: 0xfffffe0127d22000

 

13.2 works.   13.3 and 14.x panic.

 

an older system with two qlogic isp cards, isp0 and isp1, nothing attached to them, and it panics on boot with 13.3 and 14.x images.
13.2 works
 

 
 
 

Autoloading module: ichsmb
ichsmb0: <Intel 631xESB/6321ESB (ESB2) SMBus controller> port 0x300-0x31f irq 22 at device 31.3 on pci0
smbus0: <System Management Bus> on ichsmb0
isp1: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0x9c00-0x9cff mem 0xfcbfc000-0xfcbfffff irq 18 at device 0.0 on pci9
isp1: FLT[DEF]: Invalid length=0xffff(65535)
panic: vm_fault_lookup: fault on nofault entry, addr: 0xfffffe0127d22000
cpuid = 6
time = 1721060956
KDB: stack backtrace:
Uptime: 17s
Dumping 936 out of 24532 MB:..2%..11%..21%..31%..42%..52%..62%..71%..81%..91%
------------------------------------------------------------------------