Ok Basic data included
-----Original Message----- From: Ronald Klop [mailto:ronald-li...@klop.ws] Sent: 08 February 2017 12:51 To: Thomas Sparrevohn <thomas.sparrev...@btinternet.com>; FreeBSD Current <FreeBSD-current@freebsd.org> Subject: Re: gptzfsboot trouble On Wed, 08 Feb 2017 13:40:25 +0100, Thomas Sparrevohn <thomas.sparrev...@btinternet.com> wrote: > > The bug in the bugzilla could be related - what is weird is I have been > running this setup for years without issues - which I guess just shows > how good ye'ol FreeBSD still is ;-) Tried to run through the svn log but > could not immediately see anything that seemed to be related I was triggered on that bugzilla issue because of the wrong lba number. > Would the photos of the screen help? Everything helps. NB: please keep the mailinglist in the address list. There are more knowledgeable people there. Ronald. > -----Original Message----- > From: Ronald Klop [mailto:ronald-li...@klop.ws] > Sent: 08 February 2017 12:27 > To: FreeBSD-current@freebsd.org; Thomas Sparrevohn > <thomas.sparrev...@btinternet.com> > Subject: Re: gptzfsboot trouble > > On Tue, 07 Feb 2017 17:08:44 +0100, Thomas Sparrevohn > <thomas.sparrev...@btinternet.com> wrote: > >> Hi all >> >> >> Last week I decided to upgrade my FreeBSD installation - it's been a >> while (September 16 was last time). Unfortunately CURRENT does not >> boot and cash in a weird way. Both 11-RELEASE and 12 CURRENT boot >> loader seems to attempt to read blocks that exceeds the physical disk. >> Initially I through it was a hard disk error - but after a "oh" >> experience I realised that the >> "gptzfsboot: error 4 lba 921592" is actually beyond the physical >> boundaries of the disk (300GB disk). In order to rule out different >> options - I installed a vanilla 11-RELEASE on the 300G with a simple >> stripe - it also gives the error but does boot - the LBA of the error >> is slightly different on 11 CURRENT and comes up with LBA 921600 >> >> >> I have scanned all the disks for physical faults and there seems to be >> none and I have tried doing a single disk installation on each disk - >> they give the same error - Does anybody have any idea? Included Photos >> as sometimes it get through to the actual boot menu but then crash in >> another place >> >> >> I have some images - but they are 2 bit for the mailing list ;-) > > > Can it be related to this issue? > https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=144234 > > Would be nice if you tell more about the system. CPU? dmesg? > The 11-RELEASE did that boot from the same disk? In the mentioned issue > there is the case that gptzfsboot does recognize a secondary disk (can > be configured as mirror), but not the first. > > As you say UFS works, the bug might be in the gptzfsboot code, because > that is not used for UFS. > > Regards, > Ronald.
camcontrol_devlist
Description: Binary data
camcontrol_identify
Description: Binary data
Waiting (max 60 seconds) for system process `vnlru' to stop... done
Waiting (max 60 seconds) for system process `bufdaemon' to stop... done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining... 0 0 0 0 0 0 0 0 0 0 0 done
All buffers synced.
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-RELEASE-p1 #0 r306420: Thu Sep 29 01:43:23 UTC 2016
r...@releng2.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC amd64
FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based on LLVM
3.8.0)
VT(vga): resolution 640x480
CPU: Intel(R) Core(TM) i7 CPU 960 @ 3.20GHz (3208.03-MHz K8-class CPU)
Origin="GenuineIntel" Id=0x106a5 Family=0x6 Model=0x1a Stepping=5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x98e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
VT-x: PAT,HLT,MTF,PAUSE,EPT,VPID
TSC: P-state invariant, performance statistics
real memory = 12884901888 (12288 MB)
avail memory = 12401463296 (11826 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <ALWARE ALIENWRE>
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s) x 2 hardware threads
random: unblocking device.
ioapic0 <Version 2.0> irqs 0-23 on motherboard
random: entropy device external interface
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff8101c950, 0) error 19
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
acpi0: <ALWARE ALIENWRE> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 350
Event timer "HPET1" frequency 14318180 Hz quality 340
Event timer "HPET2" frequency 14318180 Hz quality 340
Event timer "HPET3" frequency 14318180 Hz quality 340
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci2: <ACPI PCI bus> on pcib2
vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem
0xd0000000-0xdfffffff,0xcf800000-0xcfffffff,0xfbc00000-0xfbc3ffff irq 16 at
device 0.0 on pci2
vgapci0: Boot video device
hdac0: <ATI (0xaac8) HDA Controller> mem 0xfbe00000-0xfbe03fff irq 17 at device
0.1 on pci2
pcib3: <ACPI PCI-PCI bridge> at device 7.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 9.0 on pci0
pci4: <ACPI PCI bus> on pcib4
pci0: <base peripheral, interrupt controller> at device 20.0 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 20.1 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 20.2 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 20.3 (no driver
attached)
uhci0: <Intel 82801JI (ICH10) USB controller USB-D> port 0xa400-0xa41f irq 16
at device 26.0 on pci0
uhci0: LegSup = 0x2f00
usbus0 on uhci0
uhci1: <Intel 82801JI (ICH10) USB controller USB-E> port 0xa480-0xa49f irq 21
at device 26.1 on pci0
uhci1: LegSup = 0x2f00
usbus1 on uhci1
uhci2: <Intel 82801JI (ICH10) USB controller USB-F> port 0xa800-0xa81f irq 19
at device 26.2 on pci0
uhci2: LegSup = 0x2f00
usbus2 on uhci2
ehci0: <Intel 82801JI (ICH10) USB 2.0 controller USB-B> mem
0xf9e00000-0xf9e003ff irq 18 at device 26.7 on pci0
usbus3: EHCI version 1.0
usbus3 on ehci0
hdac1: <Intel 82801JI HDA Controller> mem 0xfa000000-0xfa003fff irq 22 at
device 27.0 on pci0
pcib5: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pcib5: [GIANT-LOCKED]
pcib6: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pcib6: [GIANT-LOCKED]
pci5: <ACPI PCI bus> on pcib6
bge0: <Broadcom NetLink Gigabit Ethernet Controller , ASIC rev. 0x5784100>
mem 0xfb800000-0xfb80ffff irq 17 at device 0.0 on pci5
bge0: CHIP ID 0x05784100; ASIC REV 0x5784; CHIP REV 0x57841; PCI-E
miibus0: <MII bus> on bge0
brgphy0: <BCM5784 10/100/1000baseT PHY> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Using defaults for TSO: 65518/35/2048
bge0: Ethernet address: a4:ba:db:02:6f:a2
pcib7: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pcib7: [GIANT-LOCKED]
pci6: <ACPI PCI bus> on pcib7
bge1: <Broadcom NetLink Gigabit Ethernet Controller , ASIC rev. 0x5784100>
mem 0xfb600000-0xfb60ffff irq 18 at device 0.0 on pci6
bge1: CHIP ID 0x05784100; ASIC REV 0x5784; CHIP REV 0x57841; PCI-E
miibus1: <MII bus> on bge1
brgphy1: <BCM5784 10/100/1000baseT PHY> PHY 1 on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge1: Using defaults for TSO: 65518/35/2048
bge1: Ethernet address: a4:ba:db:02:6f:a1
pcib8: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pcib8: [GIANT-LOCKED]
pci7: <ACPI PCI bus> on pcib8
atapci0: <JMicron JMB363 UDMA133 controller> port
0xdc00-0xdc07,0xd880-0xd883,0xd800-0xd807,0xd480-0xd483,0xd400-0xd40f mem
0xfb200000-0xfb201fff irq 19 at device 0.0 on pci7
ahci0: <JMicron JMB363 AHCI SATA controller> at channel -1 on atapci0
ahci0: AHCI v1.00 with 2 3Gbps ports, Port Multiplier supported
ahci0: quirks=0x1<NOFORCE>
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ata2: <ATA channel> at channel 0 on atapci0
pcib9: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0
pcib9: [GIANT-LOCKED]
pci8: <ACPI PCI bus> on pcib9
siis0: <SiI3132 SATA controller> port 0xcc00-0xcc7f mem
0xfb000000-0xfb00007f,0xfae00000-0xfae03fff irq 17 at device 0.0 on pci8
siisch0: <SIIS channel> at channel 0 on siis0
siisch1: <SIIS channel> at channel 1 on siis0
uhci3: <Intel 82801JI (ICH10) USB controller USB-A> port 0xa880-0xa89f irq 23
at device 29.0 on pci0
uhci3: LegSup = 0x2f00
usbus4 on uhci3
uhci4: <Intel 82801JI (ICH10) USB controller USB-B> port 0xac00-0xac1f irq 19
at device 29.1 on pci0
uhci4: LegSup = 0x2f00
usbus5 on uhci4
uhci5: <Intel 82801JI (ICH10) USB controller USB-C> port 0xb000-0xb01f irq 18
at device 29.2 on pci0
uhci5: LegSup = 0x2f00
usbus6 on uhci5
ehci1: <Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem
0xfa200000-0xfa2003ff irq 23 at device 29.7 on pci0
usbus7: EHCI version 1.0
usbus7 on ehci1
pcib10: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci9: <ACPI PCI bus> on pcib10
pci9: <serial bus, FireWire> at device 2.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci1: <Intel ICH10 AHCI SATA controller> port
0xb880-0xb887,0xb800-0xb803,0xb480-0xb487,0xb400-0xb403,0xb080-0xb09f mem
0xfa400000-0xfa4007ff irq 19 at device 31.2 on pci0
ahci1: AHCI v1.20 with 6 3Gbps ports, Port Multiplier not supported
ahcich2: <AHCI channel> at channel 0 on ahci1
ahcich3: <AHCI channel> at channel 1 on ahci1
ahcich4: <AHCI channel> at channel 2 on ahci1
ahcich5: <AHCI channel> at channel 3 on ahci1
ahcich6: <AHCI channel> at channel 4 on ahci1
ahcich7: <AHCI channel> at channel 5 on ahci1
ahciem0: <AHCI enclosure management bridge> on ahci1
acpi_button0: <Power Button> on acpi0
qpi0: <QPI system bus> on motherboard
pcib11: <QPI Host-PCI bridge> pcibus 255 on qpi0
pci10: <PCI bus> on pcib11
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
uart0: <16550 or compatible> at port 0x3f8 irq 4 flags 0x10 on isa0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est4: <Enhanced SpeedStep Frequency Control> on cpu4
est5: <Enhanced SpeedStep Frequency Control> on cpu5
est6: <Enhanced SpeedStep Frequency Control> on cpu6
est7: <Enhanced SpeedStep Frequency Control> on cpu7
usbus0: 12Mbps Full Speed USB v1.0
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
nvme cam probe device init
hdacc0: <ATI R6xx HDA CODEC> at cad 0 on hdac0
hdaa0: <ATI R6xx Audio Function Group> at nid 1 on hdacc0
pcm0: <ATI R6xx (HDMI)> at nid 3 on hdaa0
pcm1: <ATI R6xx (HDMI)> at nid 5 on hdaa0
pcm2: <ATI R6xx (HDMI)> at nid 7 on hdaa0
pcm3: <ATI R6xx (HDMI)> at nid 9 on hdaa0
pcm4: <ATI R6xx (HDMI)> at nid 11 on hdaa0
pcm5: <ATI R6xx (HDMI)> at nid 13 on hdaa0
hdacc1: <Realtek ALC1200 HDA CODEC> at cad 0 on hdac1
hdaa1: <Realtek ALC1200 Audio Function Group> at nid 1 on hdacc1
pcm6: <Realtek ALC1200 (Analog 7.1+HP/2.0)> at nid 20,22,21,23,27 and 24,25,26
on hdaa1
pcm7: <Realtek ALC1200 (Digital)> at nid 30 on hdaa1
pcm8: <Realtek ALC1200 (Rear Digital)> at nid 17 on hdaa1
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ugen6.1: <Intel> at usbus6
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
ses0 at ahciem0 bus 0 scbus11 target 0 lun 0
ses0: <AHCI SGPIO Enclosure 1.00 0001> SEMB S-E-S 2.00 device
ses0: SEMB SES Device
ada0 at ahcich2 bus 0 scbus5 target 0 lun 0
ada0: <Samsung SSD 840 EVO 250GB EXT0BB6Q> ACS-2 ATA SATA 3.x device
ada0: Serial Number S1DFNEAD904333V
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 512bytes)
ada0: Command Queueing enabled
ada0: 238475MB (488397168 512 byte sectors)
ada0: quirks=0x3<4K,NCQ_TRIM_BROKEN>
ada1 at ahcich3 bus 0 scbus6 target 0 lun 0
ada1: <Hitachi HDP725032GLA360 GM3OA52A> ATA8-ACS SATA 2.x device
ada1: Serial Number GEB030RG03EZZH
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 305245MB (625142448 512 byte sectors)
ada2 at ahcich4 bus 0 scbus7 target 0 lun 0
ada2: <SAMSUNG HD642JJ 1AA01117> ATA-7 SATA 2.x device
ada2: Serial Number S1JNJ90Z104658
ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 610480MB (1250263728 512 byte sectors)
ada3 at ahcich5 bus 0 scbus8 target 0 lun 0
ada3: <Hitachi HDP725032GLA360 GM3OA52A> ATA8-ACS SATA 2.x device
ada3: Serial Number GEB330RC0ASTSF
ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada3: Command Queueing enabled
ada3: 305245MB (625142448 512 byte sectors)
ada4 at ahcich6 bus 0 scbus9 target 0 lun 0
ada4: <SAMSUNG HD642JJ 1AA01117> ATA-7 SATA 2.x device
ada4: Serial Number S1JNJ90Z104652
ada4: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada4: Command Queueing enabled
ada4: 610480MB (1250263728 512 byte sectors)
ada5 at ahcich7 bus 0 scbus10 target 0 lun 0
ada5: <Hitachi HDP725032GLA360 GM3OA5CA> ATA8-ACS SATA 2.x device
ada5: Serial Number GECR34RF20X7LE
ada5: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada5: Command Queueing enabled
ada5: 305245MB (625142448 512 byte sectors)
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #6 Launched!
SMP: AP CPU #7 Launched!
cd0 at ahcich0 bus 0 scbus0 target 0 lun 0
cd0: <TSSTcorp DVD+-RW TS-H653G DW10> Removable CD-ROM SCSI device
cd0: Serial Number R4606GFZ14166700
cd0: 150.000MB/s transfers (SATA 1.x, UDMA5, ATAPI 12bytes, PIO 8192bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray
closed
Timecounter "TSC-low" frequency 1604016454 Hz quality 1000
Trying to mount root from zfs:zroot/ROOT/default []...
Root mount waiting for: usbus7 usbus3
Root mount waiting for: usbus7 usbus3
uhub3: 6 ports with 6 removable, self powered
uhub7: 6 ports with 6 removable, self powered
Root mount waiting for: usbus7 usbus3
ugen3.2: <vendor 0x04b4> at usbus3
uhub8: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/90.15, addr 2> on
usbus3
Root mount waiting for: usbus7 usbus3
uhub8: 4 ports with 4 removable, self powered
ugen5.2: <Logitech> at usbus5
ukbd0: <Logitech USB Receiver, class 0/0, rev 2.00/24.01, addr 2> on usbus5
ugen0.2: <Alienware> at usbus0
kbd2 at ukbd0
ugen7.2: <Innostor> at usbus7
umass0: <Innostor PenDrive, class 0/0, rev 2.10/0.01, addr 2> on usbus7
umass0: SCSI over Bulk-Only; quirks = 0x8100
umass0:12:0: Attached to scbus12
da0 at umass-sim0 bus 0 scbus12 target 0 lun 0
da0: <Innostor Innostor 1.00> Removable Direct Access SPC-4 SCSI device
da0: Serial Number AC220B7F2408000000000000000665
da0: 40.000MB/s transfers
da0: 29620MB (60661760 512 byte sectors)
da0: quirks=0x12<NO_6_BYTE,NO_RC16>
ugen3.3: <Broadcom> at usbus3
uhub9: <Broadcom BCM2046B1, class 9/0, rev 2.00/1.00, addr 3> on usbus3
uhub9: 3 ports with 0 removable, self powered
Root mount waiting for: usbus3
ugen3.4: <vendor 0x413c> at usbus3
ukbd1: <vendor 0x413c product 0x8161, class 0/0, rev 2.00/1.00, addr 4> on
usbus3
kbd3 at ukbd1
ugen3.5: <vendor 0x413c> at usbus3
Root mount waiting for: usbus3
ugen3.6: <vendor 0x05ac> at usbus3
uhub10: <vendor 0x05ac product 0x912f, class 9/0, rev 2.00/1.01, addr 6> on
usbus3
uhub10: MTT enabled
Root mount waiting for: usbus3
uhub10: 3 ports with 2 removable, self powered
Root mount waiting for: usbus3
Root mount waiting for: usbus3
Root mount waiting for: usbus3
Root mount waiting for: usbus3
ugen3.7: <Western Digital> at usbus3
umass1: <Western Digital My Passport 0820, class 0/0, rev 2.10/10.12, addr 7>
on usbus3
umass1: SCSI over Bulk-Only; quirks = 0xc001
umass1:13:1: Attached to scbus13
ugen3.8: <vendor 0x05ac> at usbus3
Root mount waiting for: usbus3
Root mount waiting for: usbus3
ugen3.9: <LaCie> at usbus3
umass2: <LaCie P9221 Mobile Drive, class 0/0, rev 2.00/0.06, addr 9> on usbus3
umass2: SCSI over Bulk-Only; quirks = 0x8100
umass2:14:2: Attached to scbus14
(probe1:umass-sim2:2:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00
00
(probe1:umass-sim2:2:0:0): CAM status: SCSI Status Error
(probe1:umass-sim2:2:0:0): SCSI status: Check Condition
(probe1:umass-sim2:2:0:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid
command operation code)
(probe1:umass-sim2:2:0:0): Error 22, Unretryable error
da1 at umass-sim2 bus 2 scbus14 target 0 lun 0
da1: <TOSHIBA MK1059GSM GU00> Fixed Direct Access SPC-3 SCSI device
da1: Serial Number 00000000e4ed3c7b20df
da1: 40.000MB/s transfers
da1: 953869MB (1953525168 512 byte sectors)
da1: quirks=0x2<NO_6_BYTE>
da2 at umass-sim1 bus 1 scbus13 target 0 lun 0
da2: <WD My Passport 0820 1012> Fixed Direct Access SPC-4 SCSI device
da2: Serial Number 575831314142343255325654
da2: 40.000MB/s transfers
da2: 953837MB (1953458176 512 byte sectors)
da2: quirks=0x2<NO_6_BYTE>
ses1 at umass-sim1 bus 1 scbus13 target 0 lun 1
ses1: <WD SES Device 1012> Fixed Enclosure Services SPC-4 SCSI device
ses1: Serial Number 575831314142343255325654
ses1: 40.000MB/s transfers
ses1: SCSI-3 ENC Device
bge0: link state changed to DOWN
bge0: link state changed to UP
uhid0: <Alienware Gaming Desktop, class 0/0, rev 2.00/0.00, addr 2> on usbus0
uhid1: <vendor 0x05ac product 0x9221, class 0/0, rev 1.10/1.15, addr 8> on
usbus3
uhid2: <Logitech USB Receiver, class 0/0, rev 2.00/24.01, addr 2> on usbus5
ums0: <Logitech USB Receiver, class 0/0, rev 2.00/24.01, addr 2> on usbus5
ums1: <vendor 0x413c product 0x8162, class 0/0, rev 2.00/1.00, addr 5> on usbus3
ums1: 3 buttons and [XY] coordinates ID=2
ums0: 16 buttons and [XYZT] coordinates ID=2
gpart.list.ada1
Description: Binary data
gpart.show.ada1
Description: Binary data
_______________________________________________ freebsd-current@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"
