Hi,
I have a -current system (current as of 1pm EST today) which I
am trying to use with a Pioneer DVR-S201 dvd writer...
FreeBSD FreeBSD2.unx.sas.com 4.0-CURRENT FreeBSD 4.0-CURRENT #0:
Mon Feb 14 15:39:24 EST 2000
[EMAIL PROTECTED]:/usr/src/sys/compile/FreeBSD i386
The appropriate portions of dmesg:
pass6 at ahc4 bus 0 target 6 lun 0
pass6: <PIONEER DVD-R DVR-S201 1.10> Removable CD-ROM SCSI-2 device
pass6: 10.000MB/s transfers (10.000MHz, offset 15)
cd1 at ahc4 bus 0 target 6 lun 0
cd1: <PIONEER DVD-R DVR-S201 1.10> Removable CD-ROM SCSI-2 device
cd1: 10.000MB/s transfers (10.000MHz, offset 15)
cd1: cd present [1 x 2048 byte records]
When I attempt to run camcontrol against this device I
get the following:
#camcontrol inquiry cd1
(pass6:ahc4:0:6:0): data overrun detected in Data-in phase. Tag == 0x8.
(pass6:ahc4:0:6:0): Have seen Data Phase. Length = 256. NumSGs = 1.
sg[0] - Addr 0x26c2000 : Length 256
camcontrol on other devices appears to work correctly:
#camcontrol inquiry da0
pass0: < > Fixed Direct Access SCSI-0 device
pass0: Serial Number JK2556760WV28L
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
I have tried different cables and swapped scsi cards with no
luck. I have put the writer on a common card with other working
devices and on a card by itself and still get the same problem.
If anyone can point me to where to start figuring this problem
out I would appreciate it.
I have appended the entire boot -v dmesg below.
Thanks!
John
Feb 14 16:15:55 FreeBSD2 /kernel: Copyright (c) 1992-2000 The FreeBSD Project.
Feb 14 16:15:55 FreeBSD2 /kernel: Copyright (c) 1982, 1986, 1989, 1991, 1993
Feb 14 16:15:55 FreeBSD2 /kernel: The Regents of the University of California. All
rights reserved.
Feb 14 16:15:55 FreeBSD2 /kernel: FreeBSD 4.0-CURRENT #0: Mon Feb 14 15:39:24 EST 2000
Feb 14 16:15:55 FreeBSD2 /kernel:
[EMAIL PROTECTED]:/usr/src/sys/compile/FreeBSD
Feb 14 16:15:55 FreeBSD2 /kernel: Calibrating clock(s) ... TSC clock: 548655391 Hz,
i8254 clock: 1193248 Hz
Feb 14 16:15:55 FreeBSD2 /kernel: CLK_USE_I8254_CALIBRATION not specified - using
default frequency
Feb 14 16:15:55 FreeBSD2 /kernel: Timecounter "i8254" frequency 1193182 Hz
Feb 14 16:15:55 FreeBSD2 /kernel: CLK_USE_TSC_CALIBRATION not specified - using old
calibration method
Feb 14 16:15:55 FreeBSD2 /kernel: CPU: Pentium III/Pentium III Xeon (548.63-MHz
686-class CPU)
Feb 14 16:15:55 FreeBSD2 /kernel: Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Feb 14 16:15:55 FreeBSD2 /kernel:
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
Feb 14 16:15:55 FreeBSD2 /kernel: real memory = 134217728 (131072K bytes)
Feb 14 16:15:55 FreeBSD2 /kernel: Physical memory chunk(s):
Feb 14 16:15:55 FreeBSD2 /kernel: 0x00001000 - 0x0009ffff, 651264 bytes (159 pages)
Feb 14 16:15:55 FreeBSD2 /kernel: 0x0031f000 - 0x07ff7fff, 130912256 bytes (31961
pages)
Feb 14 16:15:55 FreeBSD2 /kernel: avail memory = 126844928 (123872K bytes)
Feb 14 16:15:55 FreeBSD2 /kernel: bios32: Found BIOS32 Service Directory header at
0xc00ffe80
Feb 14 16:15:55 FreeBSD2 /kernel: bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
Feb 14 16:15:55 FreeBSD2 /kernel: pcibios: PCI BIOS entry at 0xcaee
Feb 14 16:15:55 FreeBSD2 /kernel: pnpbios: Found PnP BIOS data at 0xc00fe2d0
Feb 14 16:15:55 FreeBSD2 /kernel: pnpbios: Entry = f0000:e2f4 Rev = 1.0
Feb 14 16:15:55 FreeBSD2 /kernel: Other BIOS signatures found:
Feb 14 16:15:55 FreeBSD2 /kernel: ACPI: 000fdf50
Feb 14 16:15:55 FreeBSD2 /kernel: Preloaded elf kernel "kernel" at 0xc0306000.
Feb 14 16:15:55 FreeBSD2 /kernel: ccd0-3: Concatenated disk drivers
Feb 14 16:15:55 FreeBSD2 /kernel: Pentium Pro MTRR support enabled
Feb 14 16:15:55 FreeBSD2 /kernel: md0: Malloc disk
Feb 14 16:15:55 FreeBSD2 /kernel: Creating DISK md0
Feb 14 16:15:55 FreeBSD2 /kernel: pci_open(1): mode 1 addr port (0x0cf8) is 0x80000064
Feb 14 16:15:55 FreeBSD2 /kernel: pci_open(1a): mode1res=0x80000000 (0x80000000)
Feb 14 16:15:55 FreeBSD2 /kernel: pci_cfgcheck: device 0 [class=060000] [hdr=00] is
there (id=71908086)
Feb 14 16:15:55 FreeBSD2 /kernel: npx0: <math processor> on motherboard
Feb 14 16:15:55 FreeBSD2 /kernel: npx0: INT 16 interface
Feb 14 16:15:55 FreeBSD2 /kernel: pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
Feb 14 16:15:55 FreeBSD2 /kernel: pci_open(1a): mode1res=0x80000000 (0x80000000)
Feb 14 16:15:55 FreeBSD2 /kernel: pci_cfgcheck: device 0 [class=060000] [hdr=00] is
there (id=71908086)
Feb 14 16:15:55 FreeBSD2 /kernel: pcib0: <Intel 82443BX (440 BX) host to PCI bridge>
on motherboard
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x8086, dev=0x7190, revid=0x03
Feb 14 16:15:55 FreeBSD2 /kernel: class=06-00-00, hdrtype=0x00, mfdev=0
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: map[10]: type 1, range 32, base f4000000, size 26
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x8086, dev=0x7191, revid=0x03
Feb 14 16:15:55 FreeBSD2 /kernel: class=06-04-00, hdrtype=0x01, mfdev=0
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=1 secondarybus=1
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x8086, dev=0x7110, revid=0x02
Feb 14 16:15:55 FreeBSD2 /kernel: class=06-01-00, hdrtype=0x00, mfdev=1
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x8086, dev=0x7111, revid=0x01
Feb 14 16:15:55 FreeBSD2 /kernel: class=01-01-80, hdrtype=0x00, mfdev=0
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: map[20]: type 1, range 32, base 0000ffa0, size 4
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x8086, dev=0x7112, revid=0x01
Feb 14 16:15:55 FreeBSD2 /kernel: class=0c-03-00, hdrtype=0x00, mfdev=0
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: intpin=d, irq=11
Feb 14 16:15:55 FreeBSD2 /kernel: map[20]: type 1, range 32, base 0000dce0, size 5
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x8086, dev=0x7113, revid=0x02
Feb 14 16:15:55 FreeBSD2 /kernel: class=06-80-00, hdrtype=0x00, mfdev=0
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: map[90]: type 1, range 32, base 00000850, size 4
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x9004, dev=0x8178, revid=0x00
Feb 14 16:15:55 FreeBSD2 /kernel: class=01-00-00, hdrtype=0x00, mfdev=0
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: intpin=a, irq=11
Feb 14 16:15:55 FreeBSD2 /kernel: map[10]: type 1, range 32, base 0000d800, size 8
Feb 14 16:15:55 FreeBSD2 /kernel: map[14]: type 1, range 32, base ff004000, size 12
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x9004, dev=0x7895, revid=0x03
Feb 14 16:15:55 FreeBSD2 /kernel: class=01-00-00, hdrtype=0x00, mfdev=1
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: intpin=a, irq=10
Feb 14 16:15:55 FreeBSD2 /kernel: map[10]: type 1, range 32, base 0000d400, size 8
Feb 14 16:15:55 FreeBSD2 /kernel: map[14]: type 1, range 32, base ff003000, size 12
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x9004, dev=0x7895, revid=0x03
Feb 14 16:15:55 FreeBSD2 /kernel: class=01-00-00, hdrtype=0x00, mfdev=1
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: intpin=b, irq=11
Feb 14 16:15:55 FreeBSD2 /kernel: map[10]: type 1, range 32, base 0000d000, size 8
Feb 14 16:15:55 FreeBSD2 /kernel: map[14]: type 1, range 32, base ff002000, size 12
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x9004, dev=0x7895, revid=0x03
Feb 14 16:15:55 FreeBSD2 /kernel: class=01-00-00, hdrtype=0x00, mfdev=1
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: intpin=a, irq=9
Feb 14 16:15:55 FreeBSD2 /kernel: map[10]: type 1, range 32, base 0000cc00, size 8
Feb 14 16:15:55 FreeBSD2 /kernel: map[14]: type 1, range 32, base ff001000, size 12
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x9004, dev=0x7895, revid=0x03
Feb 14 16:15:55 FreeBSD2 /kernel: class=01-00-00, hdrtype=0x00, mfdev=1
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: intpin=b, irq=11
Feb 14 16:15:55 FreeBSD2 /kernel: map[10]: type 1, range 32, base 0000c800, size 8
Feb 14 16:15:55 FreeBSD2 /kernel: map[14]: type 1, range 32, base ff000000, size 12
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x10b7, dev=0x9055, revid=0x24
Feb 14 16:15:55 FreeBSD2 /kernel: class=02-00-00, hdrtype=0x00, mfdev=0
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: intpin=a, irq=11
Feb 14 16:15:55 FreeBSD2 /kernel: map[10]: type 1, range 32, base 0000dc00, size 7
Feb 14 16:15:55 FreeBSD2 /kernel: map[14]: type 1, range 32, base ff005000, size 7
Feb 14 16:15:55 FreeBSD2 /kernel: pci0: <PCI bus> on pcib0
Feb 14 16:15:55 FreeBSD2 /kernel: pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge>
at device 1.0 on pci0
Feb 14 16:15:55 FreeBSD2 /kernel: found-> vendor=0x1002, dev=0x4742, revid=0x5c
Feb 14 16:15:55 FreeBSD2 /kernel: class=03-00-00, hdrtype=0x00, mfdev=0
Feb 14 16:15:55 FreeBSD2 /kernel: subordinatebus=0 secondarybus=0
Feb 14 16:15:55 FreeBSD2 /kernel: intpin=a, irq=9
Feb 14 16:15:55 FreeBSD2 /kernel: map[10]: type 1, range 32, base fd000000, size 24
Feb 14 16:15:55 FreeBSD2 /kernel: map[14]: type 1, range 32, base 0000ec00, size 8
Feb 14 16:15:55 FreeBSD2 /kernel: map[18]: type 1, range 32, base fcfff000, size 12
Feb 14 16:15:55 FreeBSD2 /kernel: pci1: <PCI bus> on pcib1
Feb 14 16:15:55 FreeBSD2 /kernel: vga-pci0: <ATI Mach64-GB graphics accelerator> port
0xec00-0xecff mem 0xfcfff000-0xfcffffff,0xfd000000-0xfdffffff irq 9 at device 0.0 on
pci1
Feb 14 16:15:55 FreeBSD2 /kernel: isab0: <Intel 82371AB PCI to ISA bridge> at device
7.0 on pci0
Feb 14 16:15:55 FreeBSD2 /kernel: isa0: <ISA bus> on isab0
Feb 14 16:15:55 FreeBSD2 /kernel: ata-pci0: <Intel PIIX4 ATA-33 controller> port
0xffa0-0xffaf at device 7.1 on pci0
Feb 14 16:15:55 FreeBSD2 /kernel: ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xffa0
Feb 14 16:15:55 FreeBSD2 /kernel: ata0: mask=03 status0=50 status1=00
Feb 14 16:15:55 FreeBSD2 /kernel: ata0: mask=03 status0=50 status1=00
Feb 14 16:15:55 FreeBSD2 /kernel: ata0: devices = 0x1
Feb 14 16:15:55 FreeBSD2 /kernel: ata0 at 0x01f0 irq 14 on ata-pci0
Feb 14 16:15:55 FreeBSD2 /kernel: ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xffa8
Feb 14 16:15:55 FreeBSD2 /kernel: ata1: mask=03 status0=50 status1=00
Feb 14 16:15:55 FreeBSD2 /kernel: ata1: mask=03 status0=00 status1=00
Feb 14 16:15:55 FreeBSD2 /kernel: ata1: devices = 0x4
Feb 14 16:15:55 FreeBSD2 /kernel: ata1 at 0x0170 irq 15 on ata-pci0
Feb 14 16:15:55 FreeBSD2 /kernel: pci0: Intel 82371AB/EB (PIIX4) USB controller
(vendor=0x8086, dev=0x7112) at 7.2 irq 11
Feb 14 16:15:55 FreeBSD2 /kernel: chip1: <Intel 82371AB Power management controller>
port 0x850-0x85f at device 7.3 on pci0
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: <Adaptec 2940 Ultra SCSI adapter> port
0xd800-0xd8ff mem 0xff004000-0xff004fff irq 11 at device 13.0 on pci0
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: Reading SEEPROM...done.
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: internal 50 cable not present, internal 68
cable not present
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: external cable is present
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: BIOS eeprom is present
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: High byte termination Enabled
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: Low byte termination Enabled
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
Feb 14 16:15:55 FreeBSD2 /kernel: ahc0: Downloading Sequencer Program... 415
instructions downloaded
Feb 14 16:15:55 FreeBSD2 /kernel: ahc1: <Adaptec 2940/DUAL Ultra SCSI adapter> port
0xd400-0xd4ff mem 0xff003000-0xff003fff irq 10 at device 14.0 on pci0
Feb 14 16:15:55 FreeBSD2 /kernel: ahc1: Reading SEEPROM...done.
Feb 14 16:15:55 FreeBSD2 /kernel: ahc1: internal 50 cable not present, internal 68
cable not present
Feb 14 16:15:55 FreeBSD2 /kernel: ahc1: external cable not present
Feb 14 16:15:55 FreeBSD2 /kernel: ahc1: BIOS eeprom is present
Feb 14 16:15:55 FreeBSD2 /kernel: ahc1: High byte termination Enabled
Feb 14 16:15:55 FreeBSD2 /kernel: ahc1: Low byte termination Enabled
Feb 14 16:15:55 FreeBSD2 /kernel: ahc1: aic7895 Wide Channel A, SCSI Id=7, 16/255 SCBs
Feb 14 16:15:56 FreeBSD2 /kernel: ahc1: Downloading Sequencer Program... 389
instructions downloaded
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: <Adaptec 2940/DUAL Ultra SCSI adapter> port
0xd000-0xd0ff mem 0xff002000-0xff002fff irq 11 at device 14.1 on pci0
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: Reading SEEPROM...done.
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: internal 50 cable not present, internal 68
cable not present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: external cable not present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: BIOS eeprom is present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: Low byte termination Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: aic7895 Single Channel B, SCSI Id=7, 16/255
SCBs
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: Downloading Sequencer Program... 387
instructions downloaded
Feb 14 16:15:56 FreeBSD2 /kernel: using shared irq11.
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: <Adaptec 2940/DUAL Ultra SCSI adapter> port
0xcc00-0xccff mem 0xff001000-0xff001fff irq 9 at device 15.0 on pci0
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: Reading SEEPROM...done.
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: internal 50 cable not present, internal 68
cable not present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: external cable not present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: BIOS eeprom is present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: High byte termination Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: Low byte termination Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: aic7895 Wide Channel A, SCSI Id=7, 16/255 SCBs
Feb 14 16:15:56 FreeBSD2 /kernel: ahc3: Downloading Sequencer Program... 389
instructions downloaded
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: <Adaptec 2940/DUAL Ultra SCSI adapter> port
0xc800-0xc8ff mem 0xff000000-0xff000fff irq 11 at device 15.1 on pci0
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: Reading SEEPROM...done.
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: internal 50 cable not present, internal 68
cable not present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: external cable not present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: BIOS eeprom is present
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: Low byte termination Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: aic7895 Single Channel B, SCSI Id=7, 16/255
SCBs
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: Downloading Sequencer Program... 387
instructions downloaded
Feb 14 16:15:56 FreeBSD2 /kernel: xl0: <3Com 3c905B-TX Fast Etherlink XL> port
0xdc00-0xdc7f mem 0xff005000-0xff00507f irq 11 at device 17.0 on pci0
Feb 14 16:15:56 FreeBSD2 /kernel: xl0: Ethernet address: 00:b0:d0:25:67:2a
Feb 14 16:15:56 FreeBSD2 /kernel: xl0: media options word: a
Feb 14 16:15:56 FreeBSD2 /kernel: xl0: found MII/AUTO
Feb 14 16:15:56 FreeBSD2 /kernel: miibus0: <MII bus> on xl0
Feb 14 16:15:56 FreeBSD2 /kernel: xlphy0: <3Com internal media interface> on miibus0
Feb 14 16:15:56 FreeBSD2 /kernel: xlphy0: 10baseT, 10baseT-FDX, 100baseTX,
100baseTX-FDX, auto
Feb 14 16:15:56 FreeBSD2 /kernel: bpf: xl0 attached
Feb 14 16:15:56 FreeBSD2 /kernel: Trying Read_Port at 203
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: start dependant
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding dma mask 0xa
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding dma mask 0xb
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding irq mask 0x2a0
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding io range 0x534-0x60b, size=0x4,
align=0xd4
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding io range 0x388-0x38b, size=0x4,
align=0x8
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding io range 0x220-0x24f, size=0x10,
align=0x20
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: start dependant
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding dma mask 0xb
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding irq mask 0x9aa0
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding io range 0x534-0xfff, size=0x4,
align=0x4
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding io range 0x388-0x3f3, size=0x4,
align=0x8
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: adding io range 0x220-0x26f, size=0x10,
align=0x10
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0000: end dependant
Feb 14 16:15:56 FreeBSD2 /kernel: CSC000f: start dependant
Feb 14 16:15:56 FreeBSD2 /kernel: CSC000f: adding io range 0x3a0-0x3ff, size=0x8,
align=0x8
Feb 14 16:15:56 FreeBSD2 /kernel: CSC000f: end dependant
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0010: adding io range 0xf00-0xfef, size=0x8,
align=0x8
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0003: start dependant
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0003: adding io range 0x330-0x3f1, size=0x2,
align=0x8
Feb 14 16:15:56 FreeBSD2 /kernel: CSC0003: end dependant
Feb 14 16:15:56 FreeBSD2 /kernel: isa_probe_children: disabling PnP devices
Feb 14 16:15:56 FreeBSD2 /kernel: isa_probe_children: probing non-PnP devices
Feb 14 16:15:56 FreeBSD2 /kernel: fdc0: <NEC 72065B or clone> at port
0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: fdc0: FIFO enabled, 8 bytes threshold
Feb 14 16:15:56 FreeBSD2 /kernel: fd0: <1440-KB 3.5" drive> on fdc0 drive 0
Feb 14 16:15:56 FreeBSD2 /kernel: ata-isa0: already registered as ata0
Feb 14 16:15:56 FreeBSD2 /kernel: ata-isa1: already registered as ata1
Feb 14 16:15:56 FreeBSD2 /kernel: atkbdc0: <keyboard controller (i8042)> at port
0x60-0x6f on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: atkbd0: <AT Keyboard> irq 1 on atkbdc0
Feb 14 16:15:56 FreeBSD2 /kernel: atkbd: the current kbd controller command byte 0065
Feb 14 16:15:56 FreeBSD2 /kernel: atkbd: keyboard ID 0x41ab (2)
Feb 14 16:15:56 FreeBSD2 /kernel: kbdc: RESET_KBD return code:00fa
Feb 14 16:15:56 FreeBSD2 /kernel: kbdc: RESET_KBD status:00aa
Feb 14 16:15:56 FreeBSD2 /kernel: kbd0: atkbd0, AT 101/102 (2), config:0x0,
flags:0x3d0000
Feb 14 16:15:56 FreeBSD2 /kernel: psm0: current command byte:0065
Feb 14 16:15:56 FreeBSD2 /kernel: kbdc: TEST_AUX_PORT status:0000
Feb 14 16:15:56 FreeBSD2 /kernel: kbdc: RESET_AUX return code:00fa
Feb 14 16:15:56 FreeBSD2 /kernel: kbdc: RESET_AUX status:00aa
Feb 14 16:15:56 FreeBSD2 /kernel: kbdc: RESET_AUX ID:0000
Feb 14 16:15:56 FreeBSD2 /kernel: psm: status 00 02 64
Feb 14 16:15:56 FreeBSD2 /kernel: psm: status 00 03 3c
Feb 14 16:15:56 FreeBSD2 /kernel: psm: status 00 03 64
Feb 14 16:15:56 FreeBSD2 /kernel: psm: status 00 03 64
Feb 14 16:15:56 FreeBSD2 /kernel: psm: status 10 00 64
Feb 14 16:15:56 FreeBSD2 /kernel: psm: data 08 00 00
Feb 14 16:15:56 FreeBSD2 /kernel: psm: status 00 02 64
Feb 14 16:15:56 FreeBSD2 /kernel: psm: data 08 00 00
Feb 14 16:15:56 FreeBSD2 /kernel: psm: status 00 02 64
Feb 14 16:15:56 FreeBSD2 /kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0
Feb 14 16:15:56 FreeBSD2 /kernel: psm0: model Generic PS/2 mouse, device ID 0-00, 3
buttons
Feb 14 16:15:56 FreeBSD2 /kernel: psm0: config:00000000, flags:00000000, packet size:3
Feb 14 16:15:56 FreeBSD2 /kernel: psm0: syncmask:c0, syncbits:00
Feb 14 16:15:56 FreeBSD2 /kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: fb0: vga0, vga, type:VGA (5), flags:0x7007f
Feb 14 16:15:56 FreeBSD2 /kernel: fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000
0x20000
Feb 14 16:15:56 FreeBSD2 /kernel: fb0: init mode:24, bios mode:3, current mode:24
Feb 14 16:15:56 FreeBSD2 /kernel: fb0: window:0xc00b8000 size:32k gran:32k, buf:0
size:32k
Feb 14 16:15:56 FreeBSD2 /kernel: VGA parameters upon power-up
Feb 14 16:15:56 FreeBSD2 /kernel: 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
Feb 14 16:15:56 FreeBSD2 /kernel: bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
Feb 14 16:15:56 FreeBSD2 /kernel: b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
Feb 14 16:15:56 FreeBSD2 /kernel: 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
Feb 14 16:15:56 FreeBSD2 /kernel: VGA parameters in BIOS for mode 24
Feb 14 16:15:56 FreeBSD2 /kernel: 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
Feb 14 16:15:56 FreeBSD2 /kernel: bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
Feb 14 16:15:56 FreeBSD2 /kernel: b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
Feb 14 16:15:56 FreeBSD2 /kernel: 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
Feb 14 16:15:56 FreeBSD2 /kernel: EGA/VGA parameters to be used for mode 24
Feb 14 16:15:56 FreeBSD2 /kernel: 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
Feb 14 16:15:56 FreeBSD2 /kernel: bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
Feb 14 16:15:56 FreeBSD2 /kernel: b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
Feb 14 16:15:56 FreeBSD2 /kernel: 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
Feb 14 16:15:56 FreeBSD2 /kernel: sc0: <System console> on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: sc0: VGA <16 virtual consoles, flags=0x200>
Feb 14 16:15:56 FreeBSD2 /kernel: sc0: fb0, kbd0, terminal emulator: sc (syscons
terminal)
Feb 14 16:15:56 FreeBSD2 /kernel: pcic1: not probed (disabled)
Feb 14 16:15:56 FreeBSD2 /kernel: sio0: irq maps: 0x61 0x71 0x61 0x61
Feb 14 16:15:56 FreeBSD2 /kernel: sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: sio0: type 16550A
Feb 14 16:15:56 FreeBSD2 /kernel: sio1: irq maps: 0x61 0x69 0x61 0x61
Feb 14 16:15:56 FreeBSD2 /kernel: sio1 at port 0x2f8-0x2ff irq 3 on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: sio1: type 16550A
Feb 14 16:15:56 FreeBSD2 /kernel: ppc0: parallel port found at 0x378
Feb 14 16:15:56 FreeBSD2 /kernel: ppc0: ECP SPP ECP+EPP SPP
Feb 14 16:15:56 FreeBSD2 /kernel: ppc0: <Parallel port> at port 0x378-0x37f irq 7 on
isa0
Feb 14 16:15:56 FreeBSD2 /kernel: ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in
COMPATIBLE mode
Feb 14 16:15:56 FreeBSD2 /kernel: ppc0: FIFO with 16/16/8 bytes threshold
Feb 14 16:15:56 FreeBSD2 /kernel: ppi0: <Parallel I/O> on ppbus0
Feb 14 16:15:56 FreeBSD2 /kernel: lpt0: <Printer> on ppbus0
Feb 14 16:15:56 FreeBSD2 /kernel: lpt0: Interrupt-driven port
Feb 14 16:15:56 FreeBSD2 /kernel: plip0: <PLIP network interface> on ppbus0
Feb 14 16:15:56 FreeBSD2 /kernel: bpf: lp0 attached
Feb 14 16:15:56 FreeBSD2 /kernel: isa_probe_children: probing PnP devices
Feb 14 16:15:56 FreeBSD2 /kernel: unknown0: <WSS/SB> at port
0x534-0x537,0x388-0x38b,0x220-0x22f irq 5 drq 1,0 on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: unknown1: <Game> at port 0x3a0-0x3a7 on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: unknown2: <Ctrl> at port 0xf00-0xf07 on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: unknown3: <MPU> at port 0x330-0x331 on isa0
Feb 14 16:15:56 FreeBSD2 /kernel: BIOS Geometries:
Feb 14 16:15:56 FreeBSD2 /kernel: 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads,
1..63=63 sectors
Feb 14 16:15:56 FreeBSD2 /kernel: 1:0228fe3f 0..552=553 cylinders, 0..254=255 heads,
1..63=63 sectors
Feb 14 16:15:56 FreeBSD2 /kernel: 2:0228fe3f 0..552=553 cylinders, 0..254=255 heads,
1..63=63 sectors
Feb 14 16:15:56 FreeBSD2 /kernel: 3:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads,
1..63=63 sectors
Feb 14 16:15:56 FreeBSD2 /kernel: 4:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads,
1..63=63 sectors
Feb 14 16:15:56 FreeBSD2 /kernel: 5:00f2fe3f 0..242=243 cylinders, 0..254=255 heads,
1..63=63 sectors
Feb 14 16:15:56 FreeBSD2 /kernel: 0 accounted for
Feb 14 16:15:56 FreeBSD2 /kernel: Device configuration finished.
Feb 14 16:15:56 FreeBSD2 /kernel: bpf: sl0 attached
Feb 14 16:15:56 FreeBSD2 /kernel: bpf: ppp0 attached
Feb 14 16:15:56 FreeBSD2 /kernel: new masks: bio 4008c040, tty 4003109a, net 4007189a
Feb 14 16:15:56 FreeBSD2 /kernel: bpf: lo0 attached
Feb 14 16:15:56 FreeBSD2 /kernel: Waiting 5 seconds for SCSI devices to settle
Feb 14 16:15:56 FreeBSD2 /kernel: (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0
SCBs aborted.
Feb 14 16:15:56 FreeBSD2 /kernel: (noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0
SCBs aborted.
Feb 14 16:15:56 FreeBSD2 /kernel: (noperiph:ahc2:0:-1:-1): SCSI bus reset delivered. 0
SCBs aborted.
Feb 14 16:15:56 FreeBSD2 /kernel: (noperiph:ahc3:0:-1:-1): SCSI bus reset delivered. 0
SCBs aborted.
Feb 14 16:15:56 FreeBSD2 /kernel: (noperiph:ahc4:0:-1:-1): SCSI bus reset delivered. 0
SCBs aborted.
Feb 14 16:15:56 FreeBSD2 /kernel: ata0-master: success setting up UDMA2 mode on PIIX4
chip
Feb 14 16:15:56 FreeBSD2 /kernel: ad0: <Maxtor 92049U6/RA530JN0> ATA-5 disk at ata0 as
master
Feb 14 16:15:56 FreeBSD2 /kernel: ad0: 19473MB (39882528 sectors), 39566 cyls, 16
heads, 63 S/T, 512 B/S
Feb 14 16:15:56 FreeBSD2 /kernel: ad0: 16 secs/int, 1 depth queue, UDMA33
Feb 14 16:15:56 FreeBSD2 /kernel: ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK ad0
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK wd0
Feb 14 16:15:56 FreeBSD2 /kernel: ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
Feb 14 16:15:56 FreeBSD2 /kernel: ata1-master: success setting up UDMA2 mode on PIIX4
chip
Feb 14 16:15:56 FreeBSD2 /kernel: acd0: <SAMSUNG CD-ROM SC-140F/fn10> CDROM drive at
ata1 as master
Feb 14 16:15:56 FreeBSD2 /kernel: acd0: read 6875KB/s (6875KB/s), 128KB buffer, UDMA33
Feb 14 16:15:56 FreeBSD2 /kernel: acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
Feb 14 16:15:56 FreeBSD2 /kernel: acd0: Audio: play, 255 volume levels
Feb 14 16:15:56 FreeBSD2 /kernel: acd0: Mechanism: ejectable tray
Feb 14 16:15:56 FreeBSD2 /kernel: acd0: Medium: no/blank disc inside, unlocked
Feb 14 16:15:56 FreeBSD2 /kernel: (probe33:ahc2:0:3:0): INQUIRY. CDB: 12 1 80 0 ff 0
Feb 14 16:15:56 FreeBSD2 /kernel: (probe33:ahc2:0:3:0): ILLEGAL REQUEST asc:24,0
Feb 14 16:15:56 FreeBSD2 /kernel: (probe33:ahc2:0:3:0): Invalid field in CDB
Feb 14 16:15:56 FreeBSD2 /kernel: (probe34:ahc2:0:4:0): INQUIRY. CDB: 12 1 80 0 ff 0
Feb 14 16:15:56 FreeBSD2 /kernel: (probe34:ahc2:0:4:0): ILLEGAL REQUEST asc:24,0
Feb 14 16:15:56 FreeBSD2 /kernel: (probe34:ahc2:0:4:0): Invalid field in CDB
Feb 14 16:15:56 FreeBSD2 /kernel: ahc2: target 3 synchronous at 20.0MHz, offset = 0xf
Feb 14 16:15:56 FreeBSD2 /kernel: (probe58:ahc4:0:6:0): INQUIRY. CDB: 12 1 80 0 ff 0
Feb 14 16:15:56 FreeBSD2 /kernel: (probe58:ahc4:0:6:0): ILLEGAL REQUEST asc:24,0
Feb 14 16:15:56 FreeBSD2 /kernel: (probe58:ahc4:0:6:0): Invalid field in CDB
Feb 14 16:15:56 FreeBSD2 /kernel: ahc4: target 6 synchronous at 10.0MHz, offset = 0xf
Feb 14 16:15:56 FreeBSD2 /kernel: ahc0: target 4 using 16bit transfers
Feb 14 16:15:56 FreeBSD2 /kernel: ahc0: target 4 synchronous at 20.0MHz, offset = 0x8
Feb 14 16:15:56 FreeBSD2 /kernel: ahc0: target 2 using 16bit transfers
Feb 14 16:15:56 FreeBSD2 /kernel: ahc0: target 2 synchronous at 20.0MHz, offset = 0x8
Feb 14 16:15:56 FreeBSD2 /kernel: ahc0: target 3 using 16bit transfers
Feb 14 16:15:56 FreeBSD2 /kernel: ahc0: target 3 synchronous at 20.0MHz, offset = 0x8
Feb 14 16:15:56 FreeBSD2 /kernel: ahc0: target 1 using 16bit transfers
Feb 14 16:15:56 FreeBSD2 /kernel: ahc0: target 1 synchronous at 20.0MHz, offset = 0x8
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK da0
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK da1
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK da2
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK da3
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK da4
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK cd0
Feb 14 16:15:56 FreeBSD2 /kernel: Creating DISK cd1
Feb 14 16:15:56 FreeBSD2 /kernel: pass0 at ahc0 bus 0 target 1 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: pass0: <SEAGATE ST34572W 0784> Fixed Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: pass0: Serial Number JK2556760WV28L
Feb 14 16:15:56 FreeBSD2 /kernel: pass0: 40.000MB/s transfers (20.000MHz, offset 8,
16bit), Tagged Queueing Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: pass1 at ahc0 bus 0 target 2 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: pass1: <SEAGATE ST34572W 0784> Fixed Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: pass1: Serial Number JK2733440W03D5
Feb 14 16:15:56 FreeBSD2 /kernel: pass1: 40.000MB/s transfers (20.000MHz, offset 8,
16bit), Tagged Queueing Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: pass2 at ahc0 bus 0 target 3 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: pass2: <SEAGATE ST39173W 6244> Fixed Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: pass2: Serial Number LMF5466600007936J4W7
Feb 14 16:15:56 FreeBSD2 /kernel: pass2: 40.000MB/s transfers (20.000MHz, offset 8,
16bit), Tagged Queueing Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: pass3 at ahc0 bus 0 target 4 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: pass3: <SEAGATE ST39173W 6244> Fixed Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: pass3: Serial Number LMF5266900007936HYQP
Feb 14 16:15:56 FreeBSD2 /kernel: pass3: 40.000MB/s transfers (20.000MHz, offset 8,
16bit), Tagged Queueing Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: pass4 at ahc2 bus 0 target 3 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: pass4: <iomega jaz 2GB E.16> Removable Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: pass4: 20.000MB/s transfers (20.000MHz, offset 15)
Feb 14 16:15:56 FreeBSD2 /kernel: pass5 at ahc2 bus 0 target 4 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: pass5: <YAMAHA CRW4260 1.0g> Removable CD-ROM SCSI-2
device
Feb 14 16:15:56 FreeBSD2 /kernel: pass5: 3.300MB/s transfers
Feb 14 16:15:56 FreeBSD2 /kernel: pass6 at ahc4 bus 0 target 6 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: pass6: <PIONEER DVD-R DVR-S201 1.10> Removable
CD-ROM SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: pass6: 10.000MB/s transfers (10.000MHz, offset 15)
Feb 14 16:15:56 FreeBSD2 /kernel: da0 at ahc0 bus 0 target 1 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: da0: <SEAGATE ST34572W 0784> Fixed Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: da0: Serial Number JK2556760WV28L
Feb 14 16:15:56 FreeBSD2 /kernel: da0: 40.000MB/s transfers (20.000MHz, offset 8,
16bit), Tagged Queueing Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: da0: 4340MB (8888924 512 byte sectors: 255H 63S/T
553C)
Feb 14 16:15:56 FreeBSD2 /kernel: da1 at ahc0 bus 0 target 2 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: da1: <SEAGATE ST34572W 0784> Fixed Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: da1: Serial Number JK2733440W03D5
Feb 14 16:15:56 FreeBSD2 /kernel: da1: 40.000MB/s transfers (20.000MHz, offset 8,
16bit), Tagged Queueing Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: da1: 4340MB (8888924 512 byte sectors: 255H 63S/T
553C)
Feb 14 16:15:56 FreeBSD2 /kernel: da4 at ahc2 bus 0 target 3 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: da4: <iomega jaz 2GB E.16> Removable Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: da4: 20.000MB/s transfers (20.000MHz, offset 15)
Feb 14 16:15:56 FreeBSD2 /kernel: da4: 1911MB (3915600 512 byte sectors: 255H 63S/T
243C)
Feb 14 16:15:56 FreeBSD2 /kernel: da2 at ahc0 bus 0 target 3 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: da2: <SEAGATE ST39173W 6244> Fixed Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: da2: Serial Number LMF5466600007936J4W7
Feb 14 16:15:56 FreeBSD2 /kernel: da2: 40.000MB/s transfers (20.000MHz, offset 8,
16bit), Tagged Queueing Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: da2: 8683MB (17783240 512 byte sectors: 255H 63S/T
1106C)
Feb 14 16:15:56 FreeBSD2 /kernel: da3 at ahc0 bus 0 target 4 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: da3: <SEAGATE ST39173W 6244> Fixed Direct Access
SCSI-2 device
Feb 14 16:15:56 FreeBSD2 /kernel: da3: Serial Number LMF5266900007936HYQP
Feb 14 16:15:56 FreeBSD2 /kernel: da3: 40.000MB/s transfers (20.000MHz, offset 8,
16bit), Tagged Queueing Enabled
Feb 14 16:15:56 FreeBSD2 /kernel: da3: 8683MB (17783240 512 byte sectors: 255H 63S/T
1106C)
Feb 14 16:15:56 FreeBSD2 /kernel: Mounting root from ufs:/dev/ad0s1a
Feb 14 16:15:56 FreeBSD2 /kernel: (cd0:ahc2:0:4:0): READ CD RECORDED CAPACITY. CDB: 25
0 0 0 0 0 0 0 0 0
Feb 14 16:15:56 FreeBSD2 /kernel: (cd0:ahc2:0:4:0): NOT READY asc:3a,1
Feb 14 16:15:56 FreeBSD2 /kernel: (cd0:ahc2:0:4:0): Medium not present - tray closed
Feb 14 16:15:56 FreeBSD2 /kernel: cd0 at ahc2 bus 0 target 4 lun 0
Feb 14 16:15:56 FreeBSD2 /kernel: cd0: <YAMAHA CRW4260 1.0g> Removable CD-ROM SCSI-2
device
Feb 14 16:15:56 FreeBSD2 /kernel: cd0: 3.300MB/s transfers
Feb 14 16:15:56 FreeBSD2 /kernel: cd0: Attempt to query device size failed: NOT READY,
Medium not present - tray closed
Feb 14 16:15:56 FreeBSD2 /kernel: ad0s1: type 0xa5, start 0, end = 39882527, size
39882528 : OK
Feb 14 16:15:56 FreeBSD2 /kernel: start_init: trying /sbin/init
Feb 14 16:15:56 FreeBSD2 /kernel: da0s1: type 0xa5, start 0, end = 8888923, size
8888924
Feb 14 16:15:56 FreeBSD2 /kernel: da0s1: C/H/S end 553/79/2 (88639) != end 8888923:
invalid
Feb 14 16:15:56 FreeBSD2 /kernel: da1s1: type 0xa5, start 0, end = 8888923, size
8888924
Feb 14 16:15:56 FreeBSD2 /kernel: da1s1: C/H/S end 553/79/2 (88639) != end 8888923:
invalid
Feb 14 16:15:56 FreeBSD2 /kernel: da2: invalid primary partition table: no magic
Feb 14 16:15:56 FreeBSD2 /kernel: da3: invalid primary partition table: no magic
Feb 14 16:15:57 FreeBSD2 /kernel: splash: image decoder found: logo_saver
Feb 14 16:15:58 FreeBSD2 /kernel: cd1 at ahc4 bus 0 target 6 lun 0
Feb 14 16:15:59 FreeBSD2 /kernel: cd1: <PIONEER DVD-R DVR-S201 1.10> Removable
CD-ROM SCSI-2 device
Feb 14 16:15:59 FreeBSD2 /kernel: cd1: 10.000MB/s transfers (10.000MHz, offset 15)
Feb 14 16:15:59 FreeBSD2 /kernel: cd1: cd present [1 x 2048 byte records]
Feb 14 16:15:59 FreeBSD2 cvsupd[181]: CVSup server started
Feb 14 16:15:59 FreeBSD2 cvsupd[181]: Software version: REL_16_1
Feb 14 16:15:59 FreeBSD2 cvsupd[181]: Protocol version: 16.1
Feb 14 16:15:59 FreeBSD2 cvsupd[181]: Ready to service requests
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
