On 7 Feb 00, at 18:12, Dan Langille wrote:
> I have one box which is slow to boot under -current (mind you, I've never
> run anything but -current on this box). There are two pauses. One after
> ata0 appears and another after ata-isa0 appears.
I'm reposting this as there has been no response and the box still
exhibits the original problems. Make world is about 12 hours old from a
recent cvsup. Original message follows. Any ideas? cheers
I have one box which is slow to boot under -current (mind you, I've never
run anything but -current on this box). In my previous message, there
were two excessively long pauses. One after ata0 appears and another
after ata-isa0 appears. I've been able to eliminate one of these pauses.
I removed this from my kernel:
device ata1 at isa? port IO_WD2 irq 15
All times are approximate (I had to count, no watches to hand).
This is written on the motherboard: P/I-P55TP4XE.
tia folks.
Here's dmesg after a boot -v.
[dan@buff:/usr/home/dan] $ dmesg
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #0: Tue Feb 15 00:23:48 NZDT 2000
[EMAIL PROTECTED]:/usr/src/sys/compile/BUFF
Calibrating clock(s) ... TSC clock: 99464497 Hz, i8254 clock: 1193073
Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium/P54C (99.47-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x525 Stepping = 5
Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory = 33554432 (32768K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009ffff, 651264 bytes (159 pages)
0x003cb000 - 0x01ff7fff, 29544448 bytes (7213 pages)
config> di psm0
config> di sn0
config> di lnc0
config> di le0
config> di ie0
config> di fe0
config> di cs0
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> q
avail memory = 28868608 (28192K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fb810
bios32: Entry = 0xfbcf0 (c00fbcf0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xbd20
pnpbios: Found PnP BIOS data at 0xc00fda40
pnpbios: Entry = f0000:580 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc03b2000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03b20a8.
Intel Pentium detected, installing workaround for F00F bug
md0: Malloc disk
Creating DISK md0
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=122d8086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
i586_bzero() bandwidth = 169348010 bytes/sec
bzero() bandwidth = 633713561 bytes/sec
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=122d8086)
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x122d, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x122e, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x1230, revid=0x02
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000e800, size 4
found-> vendor=0x1002, dev=0x4354, revid=0x41
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base fa000000, size 24
pci0: <PCI bus> on pcib0
CPU Inactivity timer: clocks
Peer Concurrency: enabled
CPU-to-PCI Write Bursting: enabled
PCI Streaming: enabled
Bus Concurrency: enabled
Cache: NO asynchronous secondary; L1 enabled
DRAM: no memory hole, 66 MHz refresh
Read burst timing: x-2-2-2/x-3-3-3
Write burst timing: x-3-3-3
RAS-CAS delay: 3 clocks
isab0: <Intel 82371FB PCI to ISA bridge> at device 7.0 on pci0
I/O Recovery Timing: 8-bit 1 clocks, 16-bit 1 clocks
Extended BIOS: disabled
Lower BIOS: enabled
Coprocessor IRQ13: enabled
Mouse IRQ12: disabled
Interrupt Routing: A: disabled, B: disabled, C: disabled, D: disabled
MB0: IRQ15, MB1: disabled
isa0: <ISA bus> on isab0
ata-pci0: <Intel PIIX ATA controller> port 0xe800-0xe80f at device 7.1 on
pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xe800
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0 at 0x01f0 irq 14 on ata-pci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xe808
ata1: mask=03 status0=80 status1=80
[insert 37s pause here]
ata1: mask=00 status0=ffffff80 status1=ffffff80
vga-pci0: <ATI Mach64-CT graphics accelerator> mem 0xfa000000-
0xfaffffff at device 12.0 on pci0
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fe0: not probed (disabled)
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata-isa0: already registered as ata0
adv0: not probed (disabled)
bt0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0045
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0045
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff
on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic1: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
ed0 at port 0x300-0x31f iomem 0xcc000-0xcffff irq 10 on isa0
ed0: address 00:00:c0:fc:f2:b6, type SMC8216T (16 bit)
bpf: ed0 attached
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
BIOS Geometries:
0:020a1f3f 0..522=523 cylinders, 0..31=32 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: sl0 attached
bpf: ppp0 attached
new masks: bio 40084040, tty 4003009a, net 4007049a
bpf: lo0 attached
IPsec: Initialized Security Association Processing.
ata0-master: success setting up WDMA2 mode on PIIX chip
ad0: <QUANTUM FIREBALL1280A/A63.0E00> ATA-0 disk at ata0 as
master
ad0: 1222MB (2503872 sectors), 2484 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 8 secs/int, 1 depth queue, WDMA2
ad0: piomode=4 dmamode=2 udmamode=-1 cblid=0
Creating DISK ad0
Creating DISK wd0
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 2503871, size 2503809 : OK
start_init: trying /sbin/init
here's the ata section of the kernel config file:
ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
#device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
#device atapicd # ATAPI CDROM drives
#device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI
devices
Did I miss anything else which might be useful?
--
Dan Langille - DVL Software Limited [I'm looking for more work]
The FreeBSD Diary - http://www.freebsddiary.org/
NZ FreeBSD User Group - http://www.nzfug.nz.freebsd.org/
The Racing System - http://www.racingsystem.com/
unix @ home - http://www.unixathome.org/
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
