Hi Chris - I have a projector you can take but like everyone says, you are going to have to work on it. Not sure if the sound is working.
I'm at Visual Studies Workshop in Rochester NY. Email [email protected] On Sat, Jun 6, 2020 at 6:28 PM Chris Rodriguez <[email protected]> wrote: > I’m currently in Buffalo, NY if anyone can direct towards a > repair/maintenance shop or anything like that > > On Sat, Jun 6, 2020 at 6:10 PM Eric Theise <[email protected]> wrote: > >> I'm going to take a cue from Dominic's comment about postage and ask >> where, apart from "wasn't in NYC", are you Chris Rodriguez? Frameworks is >> an international list and while plenty of its conversations have little >> connection to the poster's location, discussions involving weighty >> equipment or announcements of non-virtual screenings & workshops are tied >> to place and should be made clear. >> >> In this case people might have specific recommendations of where to look >> for equipment and people/shops who could repair it if they know your area, >> and might even have equipment in storage they'd be willing to unload. >> >> >> On Sat, Jun 6, 2020 at 2:37 PM Chris Rodriguez < >> [email protected]> wrote: >> >>> How would I go about repairing it and/or figuring out what’s wrong with >>> it? >>> >>> On Sat, Jun 6, 2020 at 5:35 PM Julian Antos < >>> [email protected]> wrote: >>> >>>> FWIW an Eiki SSL or similar would seems to be the most likely to work >>>> without issue even after sitting for many years. >>>> >>>> Elmos will have disintegrated rubber rollers, Pageants will almost >>>> certainly have sound or motor problems, and Bell and Howells will have >>>> cracked worm gears. >>>> >>>> This isn’t to say that you shouldn’t remove and clean all rollers and >>>> go over the entire film path, but an Eiki that has been sitting is probably >>>> ok and won’t need much work. Most likely the focus mechanism will have >>>> disintegrated and on older machines the belts can also turn to goo. >>>> >>>> Still, these machines should be serviced regularly if they’re expected >>>> to last. Running a projector with minor mechanical issues can damage your >>>> films AND your projector. >>>> >>>> >>>> >>>> On Sat, Jun 6, 2020 at 4:27 PM Dominic Angerame < >>>> [email protected]> wrote: >>>> >>>>> Seek and you will find. I have been able to purchase many in good >>>>> working condition. Postage is a problem and trust little on Ebay…most have >>>>> never used the one’s they are selling. I have acquired most of my >>>>> equipment >>>>> enough for two complete benches etc by constantly looking and carefully, >>>>> very carefully looking on Ebay. >>>>> >>>>> Dominic >>>>> >>>>> > On Jun 6, 2020, at 2:13 PM, Scott Dorsey <[email protected]> wrote: >>>>> > >>>>> > The problem with those freebies is that they aren't free. People >>>>> get them, >>>>> > they don't want to pay to have them cleaned and lubed before they >>>>> use them, >>>>> > and then they wreck the cams in an hour of using them dry. Budget >>>>> maybe >>>>> > $200 to $300 to have a free projector put into condition to use. >>>>> > >>>>> > Please do not apply power to a projector that has been on the shelf >>>>> for >>>>> > decades. >>>>> > --scott >>>>> > >>>>> > _______________________________________________ >>>>> > FrameWorks mailing list >>>>> > [email protected] >>>>> > https://mailman-mail5.webfaction.com/listinfo/frameworks >>>>> >>>>> _______________________________________________ >>>>> FrameWorks mailing list >>>>> [email protected] >>>>> https://mailman-mail5.webfaction.com/listinfo/frameworks >>>>> >>>> -- >>>> Julian Antos >>>> Chicago Film Society >>>> www.chicagofilmsociety.org >>>> <http://www.northwestchicagofilmsociety.org/> >>>> 773 827 8991 <(773)%20827-8991> >>>> >>>> _______________________________________________ >>>> FrameWorks mailing list >>>> [email protected] >>>> https://mailman-mail5.webfaction.com/listinfo/frameworks >>>> >>> _______________________________________________ >>> FrameWorks mailing list >>> [email protected] >>> https://mailman-mail5.webfaction.com/listinfo/frameworks >>> >> _______________________________________________ >> FrameWorks mailing list >> [email protected] >> https://mailman-mail5.webfaction.com/listinfo/frameworks >> > _______________________________________________ > FrameWorks mailing list > [email protected] > https://mailman-mail5.webfaction.com/listinfo/frameworks >
_______________________________________________ FrameWorks mailing list [email protected] https://mailman-mail5.webfaction.com/listinfo/frameworks
