Hereby the -V of a Intel Q67 chip
flashrom v1.0 on Linux 3.10.0-862.11.6.el7.x86_64 (x86_64)
flashrom is free software, get the source code at https://flashrom.org
flashrom was built with libpci 3.5.1, GCC 4.8.5 20150623 (Red Hat 4.8.5-16),
little endian
Command line (5 args): flashrom -p internal:laptop=this_is_not_a_laptop -r
bios_backup.bin -V
Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
DMI chassis-type is not specific enough.
DMI string system-manufacturer: "Dell Inc."
DMI string system-product-name: "OptiPlex 990"
DMI string system-version: "01"
DMI string baseboard-manufacturer: "Dell Inc."
DMI string baseboard-product-name: "0D6H9T"
DMI string baseboard-version: "A00"
Found chipset "Intel Q67" with PCI ID 8086:1c4e.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to [email protected] including a verbose (-V)
log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0xc61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap: not enabled
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x100000 bytes
SPI Read Configuration: prefetching disabled, caching enabled,
BIOS_CNTL = 0x02: BIOS Lock Enable: enabled, BIOS Write Enable: disabled
SPIBAR = 0x00007f698e99b000 + 0x3800
0x04: 0xe008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
Reading OPCODES... done
0x06: 0x3f00 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
0x50: 0x00000a0b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b
0x54: 0x00000000 0x58: 0x09ff0600 FREG1: BIOS region (0x00600000-0x009fffff) is
read-write.
0x5C: 0x05ff0005 0x60: 0x00040001 FREG3: Gigabit Ethernet region
(0x00001000-0x00004fff) is read-write.
Writes have been disabled for safety reasons. You can enforce write
support with the ich_spi_force programmer option, but you will most likely
harm your hardware! If you force flashrom you will get no support if
something breaks. On a few mainboards it is possible to enable write
access by setting a jumper (see its documentation or the board itself).
0x90: 0x84 (SSFS)
SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0
0x91: 0xf84030 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=3, DBC=0, SME=0, SCF=0
0x94: 0x0606 (PREOP)
0x96: 0x743b (OPTYPE)
0x98: 0x05200302 (OPMENU)
0x9c: 0x0420019f (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x00802005 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x00002005 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20
0xD0: 0x00000800 (FPB)
Enabling hardware sequencing due to multiple flash chips detected.
PROBLEMS, continuing anyway
The following protocols are supported: FWH, Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Hardware sequencing reports 2
attached SPI flash chips with a combined density of 10240 kB.
The first partition ranges from 0x000000 to 0x7fffff.
In that range are 2048 erase blocks with 4096 B each.
The second partition ranges from 0x800000 to 0x9fffff.
In that range are 512 erase blocks with 4096 B each.
Found Programmer flash chip "Opaque flash chip" (10240 kB, Programmer-specific)
mapped at physical address 0x0000000000000000.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x08, id2 0x0f, id1 is
normal flash content, id2 is normal flash content
Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x08, id2 0x0f, id1
is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x08, id2 0x0f,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xea, id2 0xd0,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x08, id2 0x0f, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity
violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity
violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity
violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x08, id2 0x0f,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1
0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is
normal flash content
Found Programmer flash chip "Opaque flash chip" (10240 kB, Programmer-specific).
Reading flash... Reading 10485760 bytes starting at 0x000000.
HSFS: FDONE=1, FCERR=1, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
FAILED.
Restoring MMIO space at 0x7f698e99e8a0
Restoring PCI config space for 00:1f:0 reg 0xdc
_______________________________________________
flashrom mailing list
[email protected]
https://mail.coreboot.org/mailman/listinfo/flashrom
