This patch removes trailing whitespace in
the digi.h file.
Signed-off-by: Lidza Louina <[email protected]>
---
drivers/staging/dgnc/digi.h | 30 +++++++++++++++---------------
1 file changed, 15 insertions(+), 15 deletions(-)
diff --git a/drivers/staging/dgnc/digi.h b/drivers/staging/dgnc/digi.h
index ab90382..8027eab 100644
--- a/drivers/staging/dgnc/digi.h
+++ b/drivers/staging/dgnc/digi.h
@@ -43,7 +43,7 @@
#define TIOCMODG ('d'<<8) | 250 /* get modem ctrl state
*/
#define TIOCMODS ('d'<<8) | 251 /* set modem ctrl state
*/
-#ifndef TIOCM_LE
+#ifndef TIOCM_LE
#define TIOCM_LE 0x01 /* line enable
*/
#define TIOCM_DTR 0x02 /* data terminal ready
*/
#define TIOCM_RTS 0x04 /* request to send
*/
@@ -122,7 +122,7 @@ struct digiflow_t {
#endif
/************************************************************************
- * Values for digi_flags
+ * Values for digi_flags
************************************************************************/
#define DIGI_IXON 0x0001 /* Handle IXON in the FEP */
#define DIGI_FAST 0x0002 /* Fast baud rates */
@@ -193,8 +193,8 @@ struct rw_t {
#define COMXI_TYPE 5 /* Board type at the designated port is a COM/Xi */
/* Non-Zero Result codes. */
-#define RESULT_NOBDFND 1 /* A Digi product at that port is not config
installed */
-#define RESULT_NODESCT 2 /* A memory descriptor was not obtainable */
+#define RESULT_NOBDFND 1 /* A Digi product at that port is not config
installed */
+#define RESULT_NODESCT 2 /* A memory descriptor was not obtainable */
#define RESULT_NOOSSIG 3 /* FEP/OS signature was not detected on the board */
#define RESULT_TOOSML 4 /* Too small an area to shrink. */
#define RESULT_NOCHAN 5 /* Channel structure for the board was not found */
@@ -205,7 +205,7 @@ struct shrink_buf_struct {
unsigned int shrink_buf_bseg; /* Amount of board memory */
unsigned int shrink_buf_hseg; /* '186 Begining of Dual-Port */
- unsigned int shrink_buf_lseg; /* '186 Begining of freed
memory */
+ unsigned int shrink_buf_lseg; /* '186 Begining of freed
memory */
unsigned int shrink_buf_mseg; /* Linear address from start of
dual-port were freed memory
begins, host viewpoint. */
@@ -220,18 +220,18 @@ struct shrink_buf_struct {
unsigned char shrink_buf_result; /* Reason for call failing
Zero is Good return */
- unsigned char shrink_buf_init; /* Non-Zero if it caused an
+ unsigned char shrink_buf_init; /* Non-Zero if it caused an
xxinit call. */
unsigned char shrink_buf_anports; /* Number of async ports */
unsigned char shrink_buf_snports; /* Number of sync ports */
unsigned char shrink_buf_type; /* Board type 1 = PC/Xi,
2 = PC/Xm,
- 3 = PC/Xe
- 4 = MC/Xi
+ 3 = PC/Xe
+ 4 = MC/Xi
5 = COMX/i */
unsigned char shrink_buf_card; /* Card number */
-
+
};
/************************************************************************
@@ -244,7 +244,7 @@ struct digi_dinfo {
};
#define DIGI_GETDD ('d'<<8) | 248 /* get driver info
*/
-
+
/************************************************************************
* Structure used with ioctl commands for per-board information
*
@@ -264,7 +264,7 @@ struct digi_info {
};
#define DIGI_GETBD ('d'<<8) | 249 /* get board info
*/
-
+
struct digi_stat {
unsigned int info_chan; /* Channel number (0 based) */
unsigned int info_brd; /* Board number (0 based) */
@@ -299,7 +299,7 @@ struct digi_ch {
};
/*
-* This structure is used with the DIGI_FEPCMD ioctl to
+* This structure is used with the DIGI_FEPCMD ioctl to
* tell the driver which port to send the command for.
*/
struct digi_cmd {
@@ -398,16 +398,16 @@ struct digi_getcounter
#define DIGI_REALPORT_GETEVENTS ('e'<<8 ) | 111
#define EV_OPU 0x0001 //!<Output paused by client
-#define EV_OPS 0x0002 //!<Output paused by reqular sw
flowctrl
+#define EV_OPS 0x0002 //!<Output paused by reqular sw flowctrl
#define EV_OPX 0x0004 //!<Output paused by extra sw flowctrl
#define EV_OPH 0x0008 //!<Output paused by hw flowctrl
#define EV_OPT 0x0800 //!<Output paused for RTS Toggle
predelay
#define EV_IPU 0x0010 //!<Input paused unconditionally by user
#define EV_IPS 0x0020 //!<Input paused by high/low water marks
-//#define EV_IPH 0x0040 //!<Input paused w/ hardware
+//#define EV_IPH 0x0040 //!<Input paused w/ hardware
#define EV_IPA 0x0400 //!<Input paused by pattern alarm module
-
+
#define EV_TXB 0x0040 //!<Transmit break pending
#define EV_TXI 0x0080 //!<Transmit immediate pending
#define EV_TXF 0x0100 //!<Transmit flowctrl char pending
--
1.8.1.2
_______________________________________________
devel mailing list
[email protected]
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
