On Sat, Oct 11, 2025 at 11:32:28AM +0800, Chaoyi Chen wrote:
> From: Chaoyi Chen <[email protected]>
>
> This patch add support for Type-C Port Controller Manager. Each PHY
> will register typec_mux and typec_switch when external Type-C
> controller is present. Type-C events are handled by TCPM without
> extcon.
>
> The extcon device should still be supported.
>
> Signed-off-by: Chaoyi Chen <[email protected]>
> ---
>
> (no changes since v5)
>
> Changes in v4:
> - Remove notify DP HPD state by USB/DP PHY.
>
> (no changes since v3)
>
> Changes in v2:
> - Fix compile error when CONFIG_TYPEC is not enabled.
> - Notify DP HPD state by USB/DP PHY.
>
> drivers/phy/rockchip/phy-rockchip-typec.c | 365 +++++++++++++++++++++-
> 1 file changed, 349 insertions(+), 16 deletions(-)
>
> @@ -850,6 +998,72 @@ static int tcphy_get_mode(struct rockchip_typec_phy
> *tcphy)
> return mode;
> }
>
> +#if IS_ENABLED(CONFIG_TYPEC)
> +static int tcphy_orien_sw_set(struct typec_switch_dev *sw,
> + enum typec_orientation orien)
> +{
> + struct rockchip_typec_phy *tcphy = typec_switch_get_drvdata(sw);
> +
> + mutex_lock(&tcphy->lock);
> +
> + if (orien == TYPEC_ORIENTATION_NONE) {
> + tcphy->new_mode = MODE_DISCONNECT;
> + goto unlock_ret;
> + }
> +
> + tcphy->flip = (orien == TYPEC_ORIENTATION_REVERSE) ? true : false;
> + tcphy->new_mode = MODE_DFP_USB;
Carrying over unanswered(!) comment from the previous series:
I don't think it is correct. Orientation defines only the cable (plug)
orientation. You should be getting the mux events for the mode
selection.
> +
> +unlock_ret:
> + mutex_unlock(&tcphy->lock);
> + return 0;
> +}
> +
> +static void udphy_orien_switch_unregister(void *data)
> +{
> + struct rockchip_typec_phy *tcphy = data;
> +
> + typec_switch_unregister(tcphy->sw);
> +}
> +
> @@ -1037,6 +1251,89 @@ static const struct phy_ops rockchip_dp_phy_ops = {
> .owner = THIS_MODULE,
> };
>
> +#if IS_ENABLED(CONFIG_TYPEC)
> +static int tcphy_typec_mux_set(struct typec_mux_dev *mux, struct
> typec_mux_state *state)
> +{
> + struct rockchip_typec_phy *tcphy = typec_mux_get_drvdata(mux);
> + struct typec_displayport_data *data;
> + int hpd = 0;
> +
> + mutex_lock(&tcphy->lock);
> +
> + switch (state->mode) {
> + case TYPEC_STATE_SAFE:
> + fallthrough;
> + case TYPEC_STATE_USB:
> + tcphy->new_mode = MODE_DFP_USB;
> + phy_set_bus_width(tcphy->phys[TYPEC_PHY_DP], 0);
> + break;
> + case TYPEC_DP_STATE_C:
> + case TYPEC_DP_STATE_E:
You need to check that altmode->svid is DP before checking for these
modes.
> + tcphy->new_mode = MODE_DFP_DP;
> + data = state->data;
> + hpd = !!(data->status & DP_STATUS_HPD_STATE);
> + phy_set_bus_width(tcphy->phys[TYPEC_PHY_DP], hpd ? 4 : 0);
> + break;
> + case TYPEC_DP_STATE_D:
> + tcphy->new_mode = MODE_DFP_DP | MODE_DFP_USB;
> + data = state->data;
> + hpd = !!(data->status & DP_STATUS_HPD_STATE);
> + phy_set_bus_width(tcphy->phys[TYPEC_PHY_DP], hpd ? 2 : 0);
> + break;
> + default:
> + break;
> + }
> +
> + mutex_unlock(&tcphy->lock);
> +
> + return 0;
> +}
> +
--
With best wishes
Dmitry
