From: Casey Connolly <[email protected]>
There are two additional supplies used by the panel, both are GPIO
controlled and are left enabled by the bootloader for continuous splash.
Previously these were (incorrectly) modelled as pinctrl. Describe them
properly so that the panel can control them.
Fixes: 288ef8a42612 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Casey Connolly <[email protected]>
Co-developed-by: David Heidelberg <[email protected]>
Signed-off-by: David Heidelberg <[email protected]>
---
.../arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi | 46 +++++++++++++++++++++-
1 file changed, 45 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
index dcfffb271fcf3..1cf03047dd7ae 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
@@ -162,6 +162,34 @@ ts_1p8_supply: ts-1p8-regulator {
enable-active-high;
regulator-boot-on;
};
+
+ panel_vci_3v3: panel-vci-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD_VCI_3V";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-0 = <&panel_vci_default>;
+ pinctrl-names = "default";
+ regulator-boot-on;
+ };
+
+ panel_vddi_poc_1p8: panel-vddi-poc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDI_POC";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-0 = <&panel_poc_default>;
+ pinctrl-names = "default";
+ regulator-boot-on;
+ };
};
&adsp_pas {
@@ -429,6 +457,8 @@ display_panel: panel@0 {
reg = <0>;
vddio-supply = <&vreg_l14a_1p88>;
+ vci-supply = <&panel_vci_3v3>;
+ poc-supply = <&panel_vddi_poc_1p8>;
reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
@@ -803,6 +833,20 @@ hall_sensor_default: hall-sensor-default-state {
bias-disable;
};
+ panel_vci_default: vci-state {
+ pins = "gpio26";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ panel_poc_default: poc-state {
+ pins = "gpio25";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
tri_state_key_default: tri-state-key-default-state {
pins = "gpio40", "gpio42", "gpio26";
function = "gpio";
@@ -818,7 +862,7 @@ ts_default_pins: ts-int-state {
};
panel_reset_pins: panel-reset-state {
- pins = "gpio6", "gpio25", "gpio26";
+ pins = "gpio6";
function = "gpio";
drive-strength = <8>;
bias-disable;
--
2.51.0
