>-----Original Message-----
>From: Dmitry Baryshkov <dmitry.barysh...@oss.qualcomm.com>
>Sent: Tuesday, September 16, 2025 6:49 PM
>To: Hermes Wu (吳佳宏) <hermes...@ite.com.tw>
>Cc: Andrzej Hajda <andrzej.ha...@intel.com>; Neil Armstrong
><neil.armstr...@linaro.org>; Robert Foss <rf...@kernel.org>; Laurent Pinchart
><laurent.pinch...@ideasonboard.com>; Jonas Karlman <jo...@kwiboo.se>; Jernej
>Skrabec <jernej.skra...@gmail.com>; Maarten Lankhorst
><maarten.lankho...@linux.intel.com>; Maxime Ripard <mrip...@kernel.org>;
>Thomas Zimmermann <tzimmerm...@suse.de>; David Airlie <airl...@gmail.com>;
>Simona Vetter <sim...@ffwll.ch>; Pet Weng (翁玉芬) <pet.w...@ite.com.tw>; Kenneth
>Hung (洪家倫) <kenneth.h...@ite.com.tw>; treapk...@chromium.org;
>dri-devel@lists.freedesktop.org; linux-ker...@vger.kernel.org
>Subject: Re: [PATCH RESEND v3 3/5] drm/bridge: it6505: modify DP link auto
>training
>
>On Tue, Sep 16, 2025 at 12:47:43PM +0800, Hermes Wu via B4 Relay wrote:
>> From: Hermes Wu <hermes...@ite.com.tw>
>>
>> IT6505 supports HW link training which will write DPCD and check
>> training status automatically.
>>
>> In the case that driver set link rate at 2.7G and HW fail to training,
>> it will change link configuration and try 1.65G. And this will cause
>> INT_VID_FIFO_ERROR triggered when link clock is changed.
>>
>> When video error occurs, video logic is reset and link training restart,
>> this will cause endless auto link training.
>>
>> Modify link auto training with disable INT_VID_FIFO_ERROR to avoid loop
>> and check INT_LINK_TRAIN_FAIL event to abort wait training done.
>>
>> Signed-off-by: Hermes Wu <hermes...@ite.com.tw>
>> ---
>> drivers/gpu/drm/bridge/ite-it6505.c | 14 +++++++++++++-
>> 1 file changed, 13 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/gpu/drm/bridge/ite-it6505.c
>> b/drivers/gpu/drm/bridge/ite-it6505.c
>> index
>> 7f6227c278a51358c70a3de93454aafeef64f2bb..f9b99c70789eea6beb3c6513155c9a4ca103d219
>> 100644
>> --- a/drivers/gpu/drm/bridge/ite-it6505.c
>> +++ b/drivers/gpu/drm/bridge/ite-it6505.c
>> @@ -1806,6 +1806,13 @@ static bool it6505_link_start_auto_train(struct
>> it6505 *it6505)
>> struct device *dev = it6505->dev;
>>
>> mutex_lock(&it6505->aux_lock);
>> +
>> + /* Disable FIFO error interrupt trigger */
>> + /* to prevent training fail loop issue */
>> + it6505_set_bits(it6505, INT_MASK_03, BIT(INT_VID_FIFO_ERROR), 0);
>> +
>> + it6505_write(it6505, INT_STATUS_03,
>> + BIT(INT_LINK_TRAIN_FAIL) | BIT(INT_VID_FIFO_ERROR));
>> it6505_set_bits(it6505, REG_TRAIN_CTRL0,
>> FORCE_CR_DONE | FORCE_EQ_DONE, 0x00);
>> /* reset link state machine and re start training*/
>> @@ -1818,8 +1825,10 @@ static bool it6505_link_start_auto_train(struct
>> it6505 *it6505)
>> link_training_state = it6505_read(it6505, REG_LINK_TRAIN_STS);
>> int03 = it6505_read(it6505, INT_STATUS_03);
>> if (int03 & BIT(INT_LINK_TRAIN_FAIL)) {
>> + /* Ignore INT_VID_FIFO_ERROR when auto training fail*/
>> it6505_write(it6505, INT_STATUS_03,
>> - BIT(INT_LINK_TRAIN_FAIL));
>> + BIT(INT_LINK_TRAIN_FAIL) |
>> + BIT(INT_VID_FIFO_ERROR));
>
>I'm really unusure about this change. Judging by the description of the
>problem, it's fix for the issue, but the issue gets introduced in the
>previous patch.
In this patch serious?
This patch serious fix this FIFO error issue, it change link training algorithm
first then fix wrong FIFO error status.
The link training process start after video status is stable, and when video
FIFO error occurs,
video stable status will also lost, link training will reset to idle and wait
until video stable again.
IT6505 HW auto training will process link training automatically, which include
CR/EQ DPCD setting, link status check,
and try lower link rate is the 2.7G cannot pass training.
In some case, DP connect to a DP sink device which cannot pass IT6505 HW auto
training.
when link auto training fail on 2.7G and IT6505 HW change link rate to 1.65G
and retry training automatically,
at this time video FIFO error will occur because of the link rate change(chip
issue), the video signal from SOC is not lost actually.
>>
>> DRM_DEV_DEBUG_DRIVER(dev,
>> "INT_LINK_TRAIN_FAIL(%x)!",
>> @@ -1837,6 +1846,9 @@ static bool it6505_link_start_auto_train(struct it6505
>> *it6505)
>> timeout--;
>> }
>> unlock:
>> + /* recover interrupt trigger*/
>> + it6505_set_bits(it6505, INT_MASK_03,
>> + BIT(INT_VID_FIFO_ERROR), BIT(INT_VID_FIFO_ERROR));
>> mutex_unlock(&it6505->aux_lock);
>>
>> return state;
>>
>> --
>> 2.34.1
>>
>>
>
>--
>With best wishes
>Dmitry
>
BR.
Hermes Wu
