On Wednesday, August 27, 2025 1:32 PM Svyatoslav wrote: > 27 серпня 2025 р. 07:09:45 GMT+03:00, Mikko Perttunen <[email protected]> пише: > >On Tuesday, August 19, 2025 9:16 PM Svyatoslav Ryhel wrote: > >> CSUS clock is required to be enabled on camera device configuration or > >> else camera module refuses to initiate properly. > >> > >> Signed-off-by: Svyatoslav Ryhel <[email protected]> > >> --- > >> > >> drivers/clk/tegra/clk-tegra20.c | 1 + > >> drivers/clk/tegra/clk-tegra30.c | 1 + > >> 2 files changed, 2 insertions(+) > >> > >> diff --git a/drivers/clk/tegra/clk-tegra20.c > >> b/drivers/clk/tegra/clk-tegra20.c index 551ef0cf0c9a..42f8150c6110 100644 > >> --- a/drivers/clk/tegra/clk-tegra20.c > >> +++ b/drivers/clk/tegra/clk-tegra20.c > >> @@ -1043,6 +1043,7 @@ static struct tegra_clk_init_table init_table[] = { > >> > >> { TEGRA20_CLK_GR3D, TEGRA20_CLK_PLL_C, 300000000, 0 }, > >> { TEGRA20_CLK_VDE, TEGRA20_CLK_PLL_C, 300000000, 0 }, > >> { TEGRA20_CLK_PWM, TEGRA20_CLK_PLL_P, 48000000, 0 }, > >> > >> + { TEGRA20_CLK_CSUS, TEGRA20_CLK_CLK_MAX, 6000000, 1 }, > >> > >> /* must be the last entry */ > >> { TEGRA20_CLK_CLK_MAX, TEGRA20_CLK_CLK_MAX, 0, 0 }, > >> > >> }; > >> > >> diff --git a/drivers/clk/tegra/clk-tegra30.c > >> b/drivers/clk/tegra/clk-tegra30.c index 82a8cb9545eb..70e85e2949e0 100644 > >> --- a/drivers/clk/tegra/clk-tegra30.c > >> +++ b/drivers/clk/tegra/clk-tegra30.c > >> @@ -1237,6 +1237,7 @@ static struct tegra_clk_init_table init_table[] = { > >> > >> { TEGRA30_CLK_HDA, TEGRA30_CLK_PLL_P, 102000000, 0 }, > >> { TEGRA30_CLK_HDA2CODEC_2X, TEGRA30_CLK_PLL_P, 48000000, 0 }, > >> { TEGRA30_CLK_PWM, TEGRA30_CLK_PLL_P, 48000000, 0 }, > >> > >> + { TEGRA30_CLK_CSUS, TEGRA30_CLK_CLK_MAX, 6000000, 1 }, > >> > >> /* must be the last entry */ > >> { TEGRA30_CLK_CLK_MAX, TEGRA30_CLK_CLK_MAX, 0, 0 }, > >> > >> }; > > > >I looked into what this clock does and it seems to be a gate for the CSUS > >pin, which provides an output clock for camera sensors (VI MCLK). Default > >source seems to be PLLC_OUT1. It would be good to note that on the commit > >message, as I can't find any documentation about the CSUS clock elsewhere. > > > >What is the 6MHz rate based on? > > 6mhz is the statistic value which I was not able to alter while testing. I > have tried 12mhz and 24mhz too but it remained 6mhz, so I left it 6mhz. > >Since this seems to be a clock consumed by the sensor, it seems to me that > >rather than making it always on, we could point to it in the sensor's > >device tree entry. > > Sensor device tree uses vi_sensor as clocks source and sensor drivers don't > support multiple linked clocks.
AIUI vi_sensor is an internal clock so the sensor cannot be receiving it directly. Perhaps the sensor is actually connected to csus, and the reason we need to enable it is to allow the vi_sensor clock to pass through the csus gate? That leaves the question of why the csus pad would be muxed to vi_sensor by default, but perhaps there's an explanation for that. > >Cheers, > >Mikko
