Hope this finds everyone well... Re: *Getting Started*, I'm continuing my proofreading; averaging 50 or so pages a day. So far, no obvious spelling / punctuation / other proofreading-type errors. There are a few word choices that could be improved, I think. But other than that nothing needs corrected; it's very nicely done.
I'm going to continue with this practice, put together a set of suggestions for wording, and also possibilities for entries in a glossary. Will keep you posted. *Michele* On Sun, May 21, 2023 at 2:07 PM Keith N. McKenna <[email protected]> wrote: > F Campos Costero wrote: > > I do see problems with the figures when I use the menu Insert -> File on > a > > blank document to insert AOO41GS2.odt. Instead of a problem with one > > figure, I saw problems with figures 2,4,11,12, and 17. The document > showed > > a placedholder rather than the actual figure. I could delete the > > placeholder and copy and paste the figures from the chapter file in most > of > > the cases. For figures 12 and 17, I had to delete the frame intended to > > hold the figure, delete the placeholder (which was somehow not in the > > frame), insert a new frame, and then copy over the figure from the > chapter > > file. > > If you turn on View -> Nonprinting Characters, you can see that figures > 12 > > and 17 are unusual. The figure caption is preceded by several empty > > paragraphs. I bet I did something wrong when I inserted those figures > long > > ago. > > I inserted AOO41GS3.odt without any problems. > > > > Regards, > > Francis > > > > On Wed, May 17, 2023 at 11:21 AM F Campos Costero <[email protected] > > > > wrote: > > > > Hi Francis; > > Thank you for looking into this. The files to be used are all at the top > level. The ones in ForWiki, already have all the front matter in them > and are strictly to create the PDFs and chapter files for distribution > on the mwiki. > > The problem was with figure 4 in AOO41GS2, which would be figure 5 in > the complete book. > > If you can correct whatever you find and finish compiling the book it > would be greatly appreciated. > > Regards > Keith > > was > >> I'll try to compile the complete book later today. To make sure we are > >> working with the same files, please confirm that: > >> 1. You are using the template file AOOdoc.ott from the Templates branch > >> 2. The odt chapter files are in the Getting-Sarted-Guide branch in the > >> ForWiki folder > >> 3. The Aoo41GSFrontMatter.odt file is the one at the top level of the > >> Getting-sarted-Guide branch. > >> > >> Which figure in chapter 1 is causing problems? > >> > >> Regards, > >> Francis > >> > >> On Wed, May 17, 2023 at 9:47 AM Keith N. McKenna < > >> [email protected]> wrote: > >> > >>> I am having difficulty compiling the Complete book for the Getting > >>> Started Guide. All the chapters except Chapter 1 (AOO41GS2) Compile > >>> perfectly. There is one figure in chapter 1 that does not come through > >>> properly. It is there in the Chapter file, but not the the complete > >>> book. If one of you could try to compile it and see if there is still a > >>> problem it would be greatly appreciated. > >>> > >>> The way I have been doing it is to create a blank writer file from the > >>> AOO Template and then insert the chapters along with any manual breaks > >>> as needed, then at the top insert Aoo41GSFrontMatter.odt which contains > >>> the Tittle Page, Copyright Page and a blank TOC. > >>> > >>> Thank a lot for the help > >>> > >>> Regards > >>> Keith > >>> > >>> > >>> --------------------------------------------------------------------- > >>> To unsubscribe, e-mail: [email protected] > >>> For additional commands, e-mail: [email protected] > >>> > >>> > > > > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [email protected] > For additional commands, e-mail: [email protected] > >
