Here is the documentation patch. I've generated the output and it works fine. Reviews are required.
Thanks, Noor On Mon, 26 Sept 2022 at 12:22, Mohd Noor Aman <nooraman5...@gmail.com> wrote: > This patch adds the relevant documentations required for booting the new > BSP. JTAG support is added for debugging. I have built the HTML docs and > verified them. > --- > user/bsps/aarch64/raspberrypi4.rst | 92 ++++++++++++++++++++++++++++++ > user/bsps/bsps-aarch64.rst | 1 + > 2 files changed, 93 insertions(+) > create mode 100644 user/bsps/aarch64/raspberrypi4.rst > > diff --git a/user/bsps/aarch64/raspberrypi4.rst > b/user/bsps/aarch64/raspberrypi4.rst > new file mode 100644 > index 0000000..94daacf > --- /dev/null > +++ b/user/bsps/aarch64/raspberrypi4.rst > @@ -0,0 +1,92 @@ > +.. SPDX-License-Identifier: CC-BY-SA-4.0 > + > +.. Copyright (C) 2022 Mohd Noor Aman > + > +.. _BSP_aarch64_Raspberrypi_4: > + > +Raspberry Pi 4B > +=============== > + > +The 'raspberrypi4b' BSP currently supports only the LP64 ABI. Raspberry > pi 4B > +and Raspberry Pi 400 are supported. The default bootloader which is used > by the > +Raspbian OS or other OS can be used to boot the RTEMS. Currently, QEMU is > not > +supported. This BSP supports the GICv2 interrupt controller. > + > +Clock Driver > +------------ > + > +The clock driver uses the `ARM Generic Timer`. > + > +Console Driver > +-------------- > + > +The console driver supports the default Qemu emulated ARM PL011 PrimeCell > UART > +as well as the physical ARM PL011 PrimeCell UART in the raspberrypi > hardware. > +Only UART0 is supported as of now. > + > +Preparing to boot > +------------------ > + > +Raspberry Pi uses a different mechanism to boot. First the GPU > initializes, > +loads the bootloader and then looks for the kernel img. By default the > arm64 > +mode looks for the ``kernel8.img``. Any other kernel can be loaded by > adding > +`kernel=<img_name>` to the ``config.txt``. > + > +The Firmware files are required in order to boot RTEMS. The latest > firmware can > +be downloaded from the `Raspberry Pi Firmware Repository > +<https://github.com/raspberrypi/firmware/>`_. USB boot is supported. All > the > +files (Firmwares and kernel) must be place in the FAT32 partition only. > Add > +``arm_64bit=1`` in the config.txt file in order to boot the BSP in 64bit > kernel > +mode. > + > + > +UART Setup > +^^^^^^^^^^ > + > +Connect your serial device to the GPIO15 and GPIO14. Add the following to > the > +config.txt file in order to use the PL011 UART0. > + > +.. code-block:: none > + > + dtoverlay = disable-bt > + enable_uart=1 > + > +Generating kernel image > +^^^^^^^^^^^^^^^^^^^^^^^ > + > +The following steps show how to run ``hello.exe`` on the BSP. Other > executables > +can be processed in a similar way. > + > +To create the kernel image: > + > +.. code-block:: shell > + > + $ aarch64-rtems@rtems-ver-major@-objcopy -Obinary hello.exe kernel8.img > + > +Copy the kernel image to the SD card. > + > +JTAG Setup > +---------- > + > +The Raspberry Pi 4 doesn't have dedicated JTAG pins. Instead, you must > configure > +the GPIO pins (GPIO22-GPIO27) to activate the JTAG functionality. The RPi > 4 > +documentation refers to this as Alt4 functions of those pins. Alt5 does > exist > +too, which goes from GPIO4, 5, 6, 12 and 13. you can check this out from > +`pinout.xyz <https://pinout.xyz/pinout/jtag#>`_ or `eLinux > +<https://elinux.org/RPi_BCM2835_GPIOs>`_ > + > +One more thing to note on JTAG with Raspberry pi 4B is that, by default, > All the > +GPIO pins are pulled down, according to the `BCM2711 documentation > +<https://datasheets.raspberrypi.com/bcm2711/bcm2711-peripherals.pdf>`_. > This > +wasn't the case in the earlier models. So in order to let the data flow > freely, > +we will have to disable them. > + > +.. code-block:: none > + > + # Disable pull downs > + gpio=22-27=np > + > + # Enable jtag pins (i.e. GPIO22-GPIO27) > + enable_jtag_gpio=1 > + > + > diff --git a/user/bsps/bsps-aarch64.rst b/user/bsps/bsps-aarch64.rst > index 933370f..f3aa15c 100644 > --- a/user/bsps/bsps-aarch64.rst > +++ b/user/bsps/bsps-aarch64.rst > @@ -9,3 +9,4 @@ aarch64 (AArch64) > .. include:: aarch64/a72.rst > .. include:: aarch64/xilinx-versal.rst > .. include:: aarch64/xilinx-zynqmp.rst > +.. include:: aarch64/raspberrypi4.rst > \ No newline at end of file > -- > 2.34.1 > >
_______________________________________________ devel mailing list devel@rtems.org http://lists.rtems.org/mailman/listinfo/devel
