Re: Network setup problems (formerly Can anyone give me a clue)

Mon, 08 Mar 2004 10:38:10 -0800

Thanks Stephen,

Here's the output of most of what you asked for.
****************************************************
lspci:
****************************************************
00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corp.: Unknown device 1131 (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82820 820 (Camino 2) Chipset PCI (rev 01)
00:1f.0 ISA bridge: Intel Corp. 82820 820 (Camino 2) Chipset ISA Bridge (ICH2) (rev 01)
00:1f.1 IDE interface: Intel Corp. 82820 820 (Camino 2) Chipset IDE U100 (rev 01)
00:1f.2 USB Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB (Hub A) (rev 01)
00:1f.3 SMBus: Intel Corp. 82820 820 (Camino 2) Chipset SMBus (rev 01)
01:09.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 78)
01:0c.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 09)
01:0d.0 Serial controller: US Robotics/3Com 56K FaxModem Model 5610 (rev 01)
02:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF
*********************************************************
ifconfig -a
**************************************************************************
eth0 Link encap:Ethernet HWaddr 00:01:03:22:E8:2B inet addr:10.254.68.202 Bcast:10.255.255.255 Mask:255.255.255.0
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:772 errors:0 dropped:0 overruns:0 frame:0
TX packets:1618 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:100963 (98.5 KiB) TX bytes:111404 (108.7 KiB)
Interrupt:3 Base address:0xcc00

lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:4891 errors:0 dropped:0 overruns:0 frame:0
TX packets:4891 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2784802 (2.6 MiB) TX bytes:2784802 (2.6 MiB)

ppp0 Link encap:Point-to-Point Protocol inet addr:207.69.249.77 P-t-P:209.165.107.192 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1524 Metric:1
RX packets:329 errors:0 dropped:0 overruns:0 frame:0
TX packets:342 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:10
RX bytes:126376 (123.4 KiB) TX bytes:23342 (22.7 KiB)
*******************************
route with eth0 not up
***************************************
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
localhost * 255.255.255.255 UH 0 0 0 lo
acn01.pa-philad * 255.255.255.255 UH 0 0 0 ppp0
default acn01.pa-philad 0.0.0.0 UG 0 0 0 ppp0
*******************************
route with eth0 up
***************************************
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
localhost * 255.255.255.255 UH 0 0 0 lo
10.254.68.0 * 255.255.255.0 U 0 0 0 eth0
**************************************
cat /procs/interrupts
*************************************
CPU0 0: 17371537 XT-PIC timer
1: 76883 XT-PIC keyboard
2: 0 XT-PIC cascade
3: 890188 XT-PIC serial
9: 0 XT-PIC es1371
13: 1 XT-PIC fpu
14: 5395229 XT-PIC ide0
15: 8 XT-PIC ide1
NMI: 0
ERR: 0
***************
dmesg
*****************
3c59x.c 16Aug00 Donald Becker and others http://www.scyld.com/network/vortex.html
eth0: 3Com 3c905C Tornado at 0xcc00, 00:01:03:22:e8:2b, IRQ 3
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 782d.
Enabling bus-master transmits and whole-frame receives.
registered device ppp0
eth0: Cannot allocate IRQ #3
eth0: Cannot allocate IRQ #3


--
To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]

Reply via email to