Hello,
I am trying to bringup the wifi network with an ipv4 address on a Cubox-i
automatically after boot.
Manually, it works:
root@outdoor:~# cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug end0
iface end0 inet dhcp
auto wlan0
iface wlan0 inet dhcp
wpa-ssid DLAN
wpa-psk <secret>
root@outdoor:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: end0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP
group default qlen 1000
link/ether d0:63:b4:00:2b:ac brd ff:ff:ff:ff:ff:ff
inet 192.168.7.25/24 brd 192.168.7.255 scope global dynamic end0
valid_lft 43121sec preferred_lft 43121sec
inet6 fe80::d263:b4ff:fe00:2bac/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP
group default qlen 1000
link/ether b8:5a:f7:82:aa:c2 brd ff:ff:ff:ff:ff:ff
inet6 fd8d:5fab:96ee:0:ba5a:f7ff:fe82:aac2/64 scope global dynamic
mngtmpaddr
valid_lft forever preferred_lft forever
inet6 fdea:6e1a:c5b2:0:ba5a:f7ff:fe82:aac2/64 scope global dynamic
mngtmpaddr
valid_lft forever preferred_lft forever
inet6 fe80::ba5a:f7ff:fe82:aac2/64 scope link
valid_lft forever preferred_lft forever
root@outdoor:~# ifdown wlan0
Killed old client process
Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/wlan0/b8:5a:f7:82:aa:c2
Sending on LPF/wlan0/b8:5a:f7:82:aa:c2
Sending on Socket/fallback
DHCPRELEASE of 192.168.2.202 on wlan0 to 192.168.2.1 port 67
ifroot@outdoor:~# ifup wlan0
Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/wlan0/b8:5a:f7:82:aa:c2
Sending on LPF/wlan0/b8:5a:f7:82:aa:c2
Sending on Socket/fallback
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
DHCPOFFER of 192.168.2.202 from 192.168.2.1
DHCPREQUEST for 192.168.2.202 on wlan0 to 255.255.255.255 port 67
DHCPACK of 192.168.2.202 from 192.168.2.1
bound to 192.168.2.202 -- renewal in 16751 seconds.
root@outdoor:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: end0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP
group default qlen 1000
link/ether d0:63:b4:00:2b:ac brd ff:ff:ff:ff:ff:ff
inet 192.168.7.25/24 brd 192.168.7.255 scope global dynamic end0
valid_lft 43062sec preferred_lft 43062sec
inet6 fe80::d263:b4ff:fe00:2bac/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP
group default qlen 1000
link/ether b8:5a:f7:82:aa:c2 brd ff:ff:ff:ff:ff:ff
inet 192.168.2.202/24 brd 192.168.2.255 scope global dynamic wlan0
valid_lft 43196sec preferred_lft 43196sec
inet6 fdea:6e1a:c5b2:0:ba5a:f7ff:fe82:aac2/64 scope global dynamic
mngtmpaddr
valid_lft forever preferred_lft forever
inet6 fd8d:5fab:96ee:0:ba5a:f7ff:fe82:aac2/64 scope global dynamic
mngtmpaddr
valid_lft forever preferred_lft forever
inet6 fe80::ba5a:f7ff:fe82:aac2/64 scope link
valid_lft forever preferred_lft forever
root@outdoor:~#
In the kernel messages I see:
[ 19.474457] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.bin (-2)
[ 19.493647] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.bin (-2)
[ 19.526434] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.txt (-2)
[ 19.552764] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.txt (-2)
[ 19.597617] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.clm_blob (-2)
[ 19.676688] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.solidrun,cubox-i-q.clm_blob (-2)
[ 19.737380] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.clm_blob (-2)
[ 19.773626] brcmfmac mmc0:0001:1: firmware: failed to load brcm/
brcmfmac4330-sdio.clm_blob (-2)
[ 23.420532] ieee80211 phy0: brcmf_p2p_create_p2pdev: timeout occurred
[ 23.427094] ieee80211 phy0: brcmf_cfg80211_add_iface: add iface p2p-dev-
wlan0 type 10 failed: err=-5
Any hint or advice is welcome.
Thanks
Rainer
--
Rainer Dorsch
http://bokomoko.de/
