root@joule:~# cat /etc/udev/rules.d/*net*
# joule:/etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.
...
# PCI device
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", \
ATTR{address}=="00:07:e9:78:a8:b0", ATTR{dev_id}=="0x0", \
ATTR{type}=="1", KERNEL=="eth*", NAME="mainboard"
...
# USB device 0x:0x (asix)
#SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", \
# ATTR{address}=="00:1d:7e:00:ee:9f", ATTR{dev_id}=="0x0", \
# ATTR{type}=="1", KERNEL=="eth*", NAME="LocLCS1788"
...
Whereas,
root@joule:~# hwinfo --netcards
20: PCI 208.0: 0200 Ethernet controller
[Created at pci.378]
Unique ID: vVa_.4AMaVDpEyvF
Parent ID: 6NW+.c7JTK_YUBi2
SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:08.0
SysFS BusID: 0000:02:08.0
Hardware Class: network
Model: "Intel 82562EZ 10/100 Ethernet Controller"
Vendor: pci 0x8086 "Intel Corporation"
Device: pci 0x1050 "82562EZ 10/100 Ethernet Controller"
SubVendor: pci 0x1028 "Dell"
SubDevice: pci 0x0155
Revision: 0x02
Driver: "e100"
Driver Modules: "e100"
Device File: LocLCS1788
Memory Range: 0xfceff000-0xfcefffff (rw,non-prefetchable)
I/O Ports: 0xddc0-0xddff (rw)
IRQ: 20 (2 events)
HW Address: 00:07:e9:78:a8:b0
Permanent HW Address: 00:07:e9:78:a8:b0
Link detected: no
Module Alias: "pci:v00008086d00001050sv00001028sd00000155bc02sc00i00"
Driver Info #0:
Driver Status: e100 is active
Driver Activation Cmd: "modprobe e100"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #10 (PCI bridge)
...
Appears that udev ignores the rule which should assign "mainboard".
How does "Device File: LocLCS1788" become associated with the
mainboard Ethernet hardware? A cache from an old configuration?
A cache in wicd?
Not surprisingly, configuration of the mainboard interface fails.
peter@joule:~$ systemctl status networking.service
b networking.service - Raise network interfaces
Loaded: loaded (/lib/systemd/system/networking.service; enabled; vendor prese
Active: failed (Result: exit-code) since Sat 2019-05-25 08:17:49 PDT; 2min 6s
Docs: man:interfaces(5)
Process: 368 ExecStart=/sbin/ifup -a --read-environment (code=exited, status=1
Process: 360 ExecStartPre=/bin/sh -c [ "$CONFIGURE_INTERFACES" != "no" ] && [
Main PID: 368 (code=exited, status=1/FAILURE)
May 25 08:17:47 joule systemd[1]: Starting Raise network interfaces...
May 25 08:17:49 joule ifup[368]: Cannot find device "mainboard"
May 25 08:17:49 joule ifup[368]: ifup: failed to bring up mainboard
May 25 08:17:49 joule systemd[1]: networking.service: Main process exited, code=
May 25 08:17:49 joule systemd[1]: Failed to start Raise network interfaces.
May 25 08:17:49 joule systemd[1]: networking.service: Unit entered failed state.
May 25 08:17:49 joule systemd[1]: networking.service: Failed with result 'exit-c
Ideas?
Thanks, ... Peter E.
--
Composed and transmitted by software designed to avoid the
complication and vulnerability of antivirus software.
Pender Is., BC: +1 604 670 0140
Bcc: peter at easthope. ca
