I am doing masquarading using my Debian machine running Sarge. Earlier I was running the default kernel that comes with Woody (2.4.18-bf14 or something). Today I upgraded to the new kernel:
/var/log# apt-get -u install kernel-image-2.4.22-1-686 kernel-doc-2.4.22 kernel-headers-2.4.22-1 kernel-pcmcia-modules-2.4.22-1-686 pcmcia-cs hotplug usbutils fxload hotplug-utils
And after this, I lost one of the NICs. I have two NICs, one is 192.168.0.1 connected to the ADSL moden, and the other is 192.168.0.2 connected to the internal LAN. So when I booted into the new kernel, the second NIC RLT8139 was not detected. But when I did pppoeconf, it listed only 1 NIC and asked if I had more which were not detected. I said Yes, and it hen allowed me to install the module for the RLT NIC. And after that it reported 2 NICs fine.
So after configuring ppp0, I could browse the net, but my internal LAN machine can't. I can't even ping that machine. I am running the same iptables rules as before. Here is what I get:
/var/log# ping 192.168.0.10
PING 192.168.0.10 (192.168.0.10): 56 data bytes
ping: sendto: Operation not permitted
ping: wrote 192.168.0.10 64 chars, ret=-1
ping: sendto: Operation not permitted
ping: wrote 192.168.0.10 64 chars, ret=-1
--- 192.168.0.10 ping statistics --- 2 packets transmitted, 0 packets received, 100% packet loss
I get this evenif I do "/etc/initd/iptables clear".
Here is my interfaces file: /etc/network# more interfaces # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
# The loopback interface auto lo iface lo inet loopback
# The first network card - this entry was created during the Debian installatio
n
# (network, broadcast and gateway are optional)
auto eth0
iface eth0 inet static
address 192.168.0.1
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
#gateway 192.168.0.0
auto eth1
iface eth1 inet static
address 192.168.0.2
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
#gateway 192.168.0.2
Any idea what could have gone wrong during installation of thsi new kernel? More information is below.
Thanks, ->HS
/var/log# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 65.94.50.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 65.94.50.1 0.0.0.0 UG 0 0 0 ppp0
/var/log# ifconfig
eth0 Link encap:Ethernet HWaddr 00:04:75:8A:D6:DF
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5932 errors:0 dropped:0 overruns:0 frame:0
TX packets:2601 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:1995603 (1.9 MiB) TX bytes:324216 (316.6 KiB)
Interrupt:9 Base address:0xd800eth1 Link encap:Ethernet HWaddr 00:50:BA:50:03:87
inet addr:192.168.0.2 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:272 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:19882 (19.4 KiB) TX bytes:0 (0.0 b)
Interrupt:9 Base address:0xd000lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:117 errors:0 dropped:0 overruns:0 frame:0
TX packets:117 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9793 (9.5 KiB) TX bytes:9793 (9.5 KiB)ppp0 Link encap:Point-to-Point Protocol
inet addr:65.94.50.150 P-t-P:65.94.50.1 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:668 errors:0 dropped:0 overruns:0 frame:0
TX packets:501 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:391058 (381.8 KiB) TX bytes:57560 (56.2 KiB)/var/log# lspci
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 03)
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 03)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 12)
00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 12)
00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 12)
00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 12)
00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 12)
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2)
02:0a.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
02:0b.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
02:0c.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
--
(Remove all underscores,_if any_, from my email address to get the correct one. Apologies for the inconvenience, but this is to reduce spam.)
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
