On Sun 18 Jun 2017 at 12:25:11 -0600, pplaw wrote: > On Sun, Jun 18, 2017 at 08:54:34PM +0300, Teemu Likonen wrote: > > pp...@pcisys.net [2017-06-18 11:43:24-06] wrote: > > __deletia__ > > > > 2: wlp1s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group > > > default qlen 1000 > > > link/ether 4c:bb:58:20:0b:cd brd ff:ff:ff:ff:ff:ff > > > 3: enx687f74158a8a: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN > > > group default qlen 1000 > > > link/ether 68:7f:74:15:8a:8a brd ff:ff:ff:ff:ff:ff > > > > > > > > > How do get at least #3 back as a useable interface, something like eth0. > > > > enx687f74158a8a is your network interface. It has a stable name that > > will never change. Just configure your system to use that interface. > > More info: > > > > https://www.debian.org/releases/stretch/amd64/release-notes/ch-whats-new.en.html#new-interface-names > > > > https://www.freedesktop.org/wiki/Software/systemd/PredictableNetworkInterfaceNames/ > > > > -- > > /// Teemu Likonen - .-.. <https://keybase.io/tlikonen> // > > // PGP: 4E10 55DC 84E9 DFF6 13D7 8557 719D 69D3 2453 9450 /// > > Thanks for the info, which explains the situation, certainly the naming > convention.
The naming convention enlightens you but it is not the problem. > The network I'm on at the moment hands out DHCP addresses. But, sometimes, > I'll hard-code the IP address for the computer (with ifconfig: ifconfig > (eth0--but in this case) enx687f74158a8a 10.x.x.x netmask 255.255.255.0; > route add default gw 10.x.x.x). Since this is a new install of Stretch, > I haven't been able to download the ifconfig package; and if I type ifup > enx687f74158a8a (or for my wireless card, wlp1s0), I get: "unknown in- > terface. But you did not do this when you installed Stretch, did you? ifconfig is in the net-tools package. d-i does not provide the package. > So, I'm in between a rock and a hard place (I can't configure the interface, > and I can't connect to a network to download the package that will let me > configure the interface). In case it would be of value, here's my lspci: The interface is capable of being configured. You do not need ifconfig. > 00:00.0 Host bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series > SoC Transaction Register (rev 0e) > 00:02.0 VGA compatible controller: Intel Corporation Atom Processor > Z36xxx/Z37xxx Series Graphics & Display (rev 0e) > 00:13.0 IDE interface: Intel Corporation Atom Processor E3800 Series SATA IDE > Controller (rev 0e) > 00:14.0 USB controller: Intel Corporation Atom Processor Z36xxx/Z37xxx, > Celeron N2000 Series USB xHCI (rev 0e) > 00:1a.0 Encryption controller: Intel Corporation Atom Processor Z36xxx/Z37xxx > Series Trusted Execution Engine (rev 0e) > 00:1b.0 Audio device: Intel Corporation Atom Processor Z36xxx/Z37xxx Series > High Definition Audio Controller (rev 0e) > 00:1c.0 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express > Root Port 1 (rev 0e) > 00:1f.0 ISA bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series > Power Control Unit (rev 0e) > 00:1f.3 SMBus: Intel Corporation Atom Processor E3800 Series SMBus Controller > (rev 0e) > 01:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless > Network Adapter (rev 01) The last line is the wireless interface. Where is the other interface? Did you install over wireless or cabled ethernet? -- Brian.
