Howdie, fellow Debianites!
Do I have to start worrying because of the following messages?
[183236.574344] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x80002
action 0x6 frozen
[183236.574352] ata1: SError: { RecovComm 10B8B }
[183236.574360] ata1.00: cmd c8/00:08:1e:a6:59/00:00:00:00:00/e0 tag 0
dma 4096 in
[183236.574362] res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask
0x4 (timeout)
[183236.574366] ata1.00: status: { DRDY }
[183236.574373] ata1: hard resetting link
[183236.894361] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[183236.894709] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[183236.895103] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[183236.895106] ata1.00: configured for UDMA/100
[183236.895117] ata1: EH complete
[183236.911503] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors
(160042 MB)
[183236.914487] sd 0:0:0:0: [sda] Write Protect is off
[183236.914492] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[183236.919286] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
The drive is less than 2 years old. The related lspci lines:
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2)
00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller
(EHCI)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge00:12.0
SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
(This is in a HP Compaq 6715b laptop). If it's of any help, this is the
output of my hdparm -iI /dev/sda:
/dev/sda:
Model=ST9160821AS , FwRev=3.BHE ,
SerialNo=5MA73N5K
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=?16?
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=312581808
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7
* signifies the current active mode
ATA device, with non-removable media
Model Number: ST9160821AS
Serial Number: 5MA73N5K
Firmware Revision: 3.BHE
Standards:
Supported: 7 6 5 4
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Standby timer values: spec'd by Standard, no device specific
minimum
R/W multiple sector transfer: Max = 16 Current = ?
Advanced power management level: 254
Recommended acoustic management value: 254, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow
control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* IDLE_IMMEDIATE with UNLOAD
* SATA-I signaling speed (1.5Gb/s)
* Phy event counters
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
supported: enhanced erase
88min for SECURITY ERASE UNIT. 88min for ENHANCED SECURITY
ERASE UNIT.
Checksum: correct
TIA and sorry for the long post!
--
Regards,
Klistvud
Certifiable Loonix User #481801
http://bufferoverflow.tiddlyspot.com
--
To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
