So I upgraded to Lenny over the weekend, and now I'm having issues with my
RAID1 were there weren't any before. Every few hours one of the devices
making up any /dev/md will fail. It's usually on /dev/sdb but it's happening
on /dev/sda as well. I can set the device faulty in mdadm and then readd and
it builds fine, but then fails again 4 or 5 hours later. I'm new to Linux
software RAID so i'm hoping someone can point me in the right direction.
Here's some of the output from dmesg:
[144376.558796] ata2.00: status: { DRDY }
[144381.956229] ata2: link is slow to respond, please be patient (ready=0)
[144387.540534] ata2: device not ready (errno=-16), forcing hardreset
[144387.540577] ata2: soft resetting link
[144387.793049] ata2.00: configured for UDMA/133
[144387.793095] ata2: EH complete
[144387.793564] sd 1:0:0:0: [sdb] 2930277168 512-byte hardware sectors
(1500302
MB)
[144387.816527] end_request: I/O error, dev sdb, sector 10313569
[144387.816527] md: super_written gets error=-5, uptodate=0
[144387.816527] raid1: Disk failure on sdb5, disabling device.
[144387.816527] raid1: Operation continuing on 1 devices.
[144387.816527] sd 1:0:0:0: [sdb] Write Protect is off
[144387.816527] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[144387.816527] RAID1 conf printout:
[144387.816527] --- wd:1 rd:2
[144387.816527] disk 0, wo:0, o:1, dev:sda5
[144387.816527] disk 1, wo:1, o:0, dev:sdb5
[144387.816527] RAID1 conf printout:
[144387.816527] --- wd:1 rd:2
[144387.816527] disk 0, wo:0, o:1, dev:sda5
[144387.816527] disk 1, wo:1, o:0, dev:sdb5
[144387.816527] RAID1 conf printout:
[144387.816527] --- wd:1 rd:2
[144387.816527] disk 0, wo:0, o:1, dev:sda5
[144387.848526] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[144528.694180] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
frozen
[144528.694227] ata1.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[144528.694231] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4
(timeout)
[144528.694317] ata1.00: status: { DRDY }
[144534.215757] ata1: link is slow to respond, please be patient (ready=0)
[144539.581347] ata1: device not ready (errno=-16), forcing hardreset
[144539.581390] ata1: soft resetting link
[144539.873328] ata1.00: configured for UDMA/133
[144539.873328] ata1: EH complete
[144539.873328] sd 0:0:0:0: [sda] 2930277168 512-byte hardware sectors
(1500302 MB)
[144539.901029] end_request: I/O error, dev sda, sector 10313569
[144539.901029] md: super_written gets error=-5, uptodate=0
[144539.901029] sd 0:0:0:0: [sda] Write Protect is off
[144539.901029] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[144539.916264] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[144818.556533] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
frozen
[144818.556579] ata2.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[144818.556583] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4
(timeout)
[144818.556667] ata2.00: status: { DRDY }
[144823.887918] ata2: link is slow to respond, please be patient (ready=0)
[144829.469773] ata2: device not ready (errno=-16), forcing hardreset
[144829.469816] ata2: soft resetting link
[144829.746129] ata2.00: configured for UDMA/133
[144829.746129] ata2: EH complete
:
Thanks for any assistance,
Ryan
