It is the touchpad of my laptop (i.e. internal). No clue why it is problematic. I'll try to write some udev rules and report any progress.
André On Mon, Dec 22, 2008 at 09:58, yiyong lin <lyy.he...@gmail.com> wrote: > I think it should be the last component appeared. "input: SynPS/2 > Synaptics TouchPad as /class/input/input10" > > is that an external component or internal? > > > > > > 2008/12/22 André Neves <andrechale...@gmail.com> > >> Hmm... Would anybody have any suggestions on finding what hardware causes >> the delay? >> >> André >> >> >> On Mon, Dec 22, 2008 at 09:44, yiyong lin <lyy.he...@gmail.com> wrote: >> >>> It looks like some of our hardware is not recognised at boot time. >>> similar to my external hard drive, sometimes, it just hangs there until i >>> unplug my hard drive, then it works fine. >>> >>> >>> >>> >>> 2008/12/22 André Neves <andrechale...@gmail.com> >>> >>> Hi, >>>> >>>> For several months now I've had my laptop boot delayed because udev >>>> likes to hang for 30 seconds after its execution on startup. I have a Dell >>>> Vostro 1500 laptop and am currently using Lenny. >>>> >>>> My rcS.d is: >>>> >>>> S01glibc.sh >>>> S02hostname.sh >>>> S02mountkernfs.sh >>>> S03udev >>>> S04hibernate >>>> ... others ... >>>> >>>> The "critical" part startup goes like this: >>>> >>>> [ 9.437162] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, >>>> low) -> IRQ 17 >>>> [ 9.466025] ACPI: Video Device [VID2] (multi-head: yes rom: no >>>> post: no) >>>> [ 9.517276] input: PC Speaker as /class/input/input9 >>>> [ 9.726175] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, >>>> low) -> IRQ 21 >>>> [ 9.732487] PCI: Setting latency timer of device 0000:00:1b.0 to 64 >>>> [ 9.853371] b43-phy0: Broadcom 4311 WLAN found >>>> [ 9.921371] phy0: Selected rate control algorithm 'pid' >>>> [ 10.096229] Broadcom 43xx driver loaded [ Features: PMLR, >>>> Firmware-ID: FW13 ] >>>> [ 10.099699] udev: renamed network interface wmaster0 to eth2 >>>> [ 10.267144] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: >>>> 0xa04793/0x300000 >>>> [ 10.267144] serio: Synaptics pass-through port at >>>> isa0060/serio1/input0 >>>> [ 10.305299] input: SynPS/2 Synaptics TouchPad as /class/input/input10 >>>> >>>> HANGS FOR ~30s >>>> >>>> Invalidating stale software suspend images... >>>> >>>> Pressing Ctrl+C when it's hanged does make it go. >>>> >>>> Any thoughts? >>>> >>>> André >>>> >>> >>> >>> >>> -- >>> Yiyong Lin >>> >>> Simplicity: >>> >>> There's an infinite number of ways to make a simple problem seem >>> difficult; >>> only a handful to make a difficult problem seem simple >>> >>> — Crenshaw's Law #1 >>> KISS (Keep it Simple, Sydney) >>> >>> — Crenshaw's Law #2 >>> Simplify, and add lightness >>> >>> — Race car designer George Miller (oft attributed to others) >>> >> >> > > > -- > Yiyong Lin > > Simplicity: > > There's an infinite number of ways to make a simple problem seem difficult; > > only a handful to make a difficult problem seem simple > > — Crenshaw's Law #1 > KISS (Keep it Simple, Sydney) > > — Crenshaw's Law #2 > Simplify, and add lightness > > — Race car designer George Miller (oft attributed to others) >
