Please find output of the above commands and file:
more /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 10.40.35.35 netmask 255.255.255.0 network 10.40.35.0 broadcast 10.40.35.255 gateway 10.40.35.1 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 10.40.35.1 auto eth0 iface eth2 inet static address 10.40.35.35 netmask 255.255.255.0 gateway 10.40.35.1 ________________________________________________________________________________________________ dmesg Linux version 2.6.18-4-686 (Debian 2.6.18.dfsg.1-12) ([EMAIL PROTECTED]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 17:17:36 UTC 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ef2fc00 (usable) BIOS-e820: 000000001ef2fc00 - 000000001ef30000 (ACPI NVS) BIOS-e820: 000000001ef30000 - 000000001ef40000 (ACPI data) BIOS-e820: 000000001ef40000 - 000000001eff0000 (ACPI NVS) BIOS-e820: 000000001eff0000 - 000000001f000000 (reserved) BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved) BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved) 0MB HIGHMEM available. 495MB LOWMEM available. found SMP MP-table at 000ff780 On node 0 totalpages: 126767 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 122671 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 ACPIAM ) @ 0x000f61b0 ACPI: RSDT (v001 INTEL D865GBF 0x20040622 MSFT 0x00000097) @ 0x1ef30000 ACPI: FADT (v002 INTEL D865GBF 0x20040622 MSFT 0x00000097) @ 0x1ef30200 ACPI: MADT (v001 INTEL D865GBF 0x20040622 MSFT 0x00000097) @ 0x1ef30300 ACPI: ASF! (v016 LEGEND I865PASF 0x00000001 MSFT 0x0100000d) @ 0x1ef345b0 ACPI: TCPA (v001 INTEL TBLOEMID 0x00000001 MSFT 0x00000097) @ 0x1ef34649 ACPI: WDDT (v001 INTEL OEMWDDT 0x00000001 MSFT 0x0100000d) @ 0x1ef3467d ACPI: DSDT (v001 INTEL D865GBF 0x00000001 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:3 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:3 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 20000000 (gap: 1f000000:dfcf0000) Detected 2992.811 MHz processor. Built 1 zonelists. Total pages: 126767 Kernel command line: root=/dev/hdb1 ro mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 494640k/507068k available (1544k kernel code, 11864k reserved, 577k data, 196k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5989.54 BogoMIPS (lpj=11979085) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 00000180 0000441d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20060707 CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5985.45 BogoMIPS (lpj=11970905) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000 monitor/mwait feature present. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 00000180 0000441d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04 Total of 2 processors activated (11974.99 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=31 checking if image is initramfs... it is Freeing initrd memory: 4782k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:02.0 PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0500-053f claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 14 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:0c: ioport range 0x400-0x47f could not be reserved pnp: 00:0c: ioport range 0x680-0x6ff has been reserved pnp: 00:0c: ioport range 0x500-0x53f has been reserved PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 PCI: Bridge: 0000:00:1e.0 IO window: b000-bfff MEM window: ff800000-ff8fffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered audit: initializing netlink socket (disabled) audit(1188685243.968:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Starting balanced_irq Using IPI No-Shortcut mode ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 196k freed input: AT Translated Set 2 keyboard as /class/input/input0 Time: tsc clocksource has been installed. ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Processor [CPU2] (supports 8 throttling states) usbcore: registered new driver usbfs usbcore: registered new driver hub Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH5: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169 ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... USB Universal Host Controller Interface driver v3.0 8139too Fast Ethernet driver 0.9.27 hda: ST3160215A, ATA DISK drive hdb: SAMSUNG SP0802N, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: SONY DVD RW AW-G170A, ATAPI CD/DVD-ROM drive hdd: SONY CD-RW CRX230ED, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 177, io base 0x0000c800 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 185, io base 0x0000cc00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000d000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 177, io base 0x0000d400 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 193, io mem 0xffa7fc00 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 201 eth0: RealTek RTL8139 at 0xb800, 00:08:a1:66:6e:62, IRQ 201 eth0: Identified 8139 chip type 'RTL-8100B/8139D' SCSI subsystem initialized 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) libata version 2.00 loaded. ata_piix 0000:00:1f.2: version 2.00 ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0xE800 ctl 0xE402 bmdma 0xD800 irq 169 ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xDC02 bmdma 0xD808 irq 169 scsi0 : ata_piix hda: max request size: 512KiB hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 hda7 > ATA: abnormal status 0x7F on port 0xE807 scsi1 : ata_piix hdb: max request size: 512KiB hdb: Host Protected Area detected. current capacity is 66055248 sectors (33820 MB) native capacity is 156368016 sectors (80060 MB) hdb: Host Protected Area disabled. hdb: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) hdb: cache flushes supported hdb: hdb1 hdb2 < hdb5 hdb6 > hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) ATA: abnormal status 0x7F on port 0xE007 Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 201 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 865 Chipset. agpgart: Detected 16252K stolen memory. agpgart: AGP aperture is 128M @ 0xf0000000 input: PC Speaker as /class/input/input1 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 intel_rng: FWH not detected Real Time Clock Driver v1.12ac parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0_measure_ac97_clock: measured 59201 usecs intel8x0: clocking to 48000 input: ImExPS/2 Generic Explorer Mouse as /class/input/input2 ts: Compaq touchscreen protocol output Adding 9767480k swap on /dev/hdb6. Priority:-1 extents:1 across:9767480k EXT3 FS on hdb1, internal journal loop: loaded (max 8 devices) device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL PROTECTED] kjournald starting. Commit interval 5 seconds EXT3 FS on hdb5, internal journal EXT3-fs: mounted filesystem with ordered data mode. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] lp0: using parport0 (interrupt-driven). ppdev: user-space parallel port driver eth0: no IPv6 routers present NET: Registered protocol family 5 Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 [drm] Initialized drm 1.0.1 20051102 ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177 [drm] Initialized i915 1.5.0 20060119 on minor 0 _______________________________________________________________________________________________ lspci 00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) 00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02) 00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02) 01:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ________________________________________________________________________________________________ On 9/1/07, Kevin Mark <[EMAIL PROTECTED]> wrote: > > On Sat, Sep 01, 2007 at 09:13:16PM +0530, Yazad Khambata wrote: > > Hi Guys, > > I'm relatively new to Linux... I installed Debian 4.0 on my PC (I > also have > > XP and 2000) on my system. Today morning I could finally configure > things right > > and could connect to the internet(I'm using a broadband connection - > Sify)... > > but then something went wrong with my network slot and there was no > network > > detected on any of my OSs, I changed the network cards slot and things > work > > fine on Windows XP and 2000; however, despite configuring the network > card (I > > entered the static Ip, gateway,netmask, primary and secondry dsn); I can > assure > > you that the config is proper; I am unable to even ping the server... > when i > > ping i get 90+% loss of packets. > > Could anyone please advise me? Many thanks to all in advance. > > Regards, > > Yazad Khambata. > also what about '/etc/network/interfaces' and 'dmesg'. You seem to > indicate that you are using a static ip but most services use dhcp or > dynamic addresses. > -K > -- > | .''`. == Debian GNU/Linux == | my web site: | > | : :' : The Universal |mysite.verizon.net/kevin.mark/| > | `. `' Operating System | go to counter.li.org and | > | `- http://www.debian.org/ | be counted! #238656 | > | my keyserver: subkeys.pgp.net | my NPO: cfsg.org | > |join the new debian-community.org to help Debian! | > |_______ Unless I ask to be CCd, assume I am subscribed _______| > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact > [EMAIL PROTECTED] > >
