-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Justin, here is the output from smartctl -a /dev/hda
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: MAXTOR STM3160812A Serial Number: 4LS62YAM Firmware Version: 3.AAK User Capacity: 160,041,885,696 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Aug 6 13:50:49 2007 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off supp ort. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 114 095 006 Pre-fail Always - 74351205 3 Spin_Up_Time 0x0003 093 092 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 72 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail Always - 84026551 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 828 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 82 187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Unknown_Attribute 0x0022 065 055 045 Old_age Always - 740425763 194 Temperature_Celsius 0x0022 035 045 000 Old_age Always - 35 (Lifetime Min/Max 0/11) 195 Hardware_ECC_Recovered 0x001a 056 048 000 Old_age Always - 6712323 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 26 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 39 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 39 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT 25 00 08 00 00 00 e0 00 00:01:05.759 READ DMA EXT 10 00 3f 00 00 00 e0 00 00:01:05.309 RECALIBRATE [OBS-4] 25 00 08 00 00 00 e0 00 00:01:05.309 READ DMA EXT 25 00 08 00 00 00 e0 00 00:01:04.858 READ DMA EXT Error 38 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT 10 00 3f 00 00 00 e0 00 00:01:02.091 RECALIBRATE [OBS-4] 25 00 08 00 00 00 e0 00 00:01:05.309 READ DMA EXT 25 00 08 00 00 00 e0 00 00:01:05.309 READ DMA EXT 25 00 08 00 00 00 e0 00 00:01:04.858 READ DMA EXT Error 37 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT 25 00 08 00 00 00 e0 00 00:01:02.091 READ DMA EXT 25 00 08 00 00 00 e0 00 00:01:02.072 READ DMA EXT c6 00 10 00 00 00 e0 00 00:01:01.621 SET MULTIPLE MODE 00 00 40 00 00 00 00 06 00:01:04.858 NOP [Abort queued commands] Error 36 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT 25 00 08 00 00 00 e0 00 00:01:02.091 READ DMA EXT c6 00 10 00 00 00 e0 00 00:01:02.072 SET MULTIPLE MODE 00 00 40 00 00 00 00 06 00:01:01.621 NOP [Abort queued commands] ef 03 40 00 00 00 e0 02 00:01:01.171 SET FEATURES [Set transfer mode] Error 35 occurred at disk power-on lifetime: 19 hours (0 days + 19 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 e0 00 00:01:02.122 READ DMA EXT c6 00 10 00 00 00 e0 00 00:01:02.091 SET MULTIPLE MODE 00 00 40 00 00 00 00 06 00:01:02.072 NOP [Abort queued commands] ef 03 40 00 00 00 e0 02 00:01:01.621 SET FEATURES [Set transfer mode] 25 00 08 00 00 00 e0 00 00:01:01.171 READ DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error # 1 Extended offline Completed without error 00% 812 - # 2 Extended offline Completed without error 00% 825 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Thanks, Sam -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.6 (GNU/Linux) Comment: http://firegpg.tuxfamily.org iD8DBQFGt2FyMwtNS8TLpaIRAr3vAKDZJ1lS5mh3nooBO6U42lQX5BXk6wCfXUTL kFNyy2fRShyO0BVy1vVIcXs= =vKd7 -----END PGP SIGNATURE----- On 8/6/07, Justin Piszcz <[EMAIL PROTECTED]> wrote: > > > > On Mon, 6 Aug 2007, David Brodbeck wrote: > > > > > On Aug 6, 2007, at 9:56 AM, Sam wrote: > > > >> Hi All, > >> I noticed this in dmesg the other day > >> > >> hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error } > >> hda: drive_cmd: error=0x04 { DriveStatusError } > >> ide: failed opcode was: 0xb0 > >> > >> and i have started to get corrupted data off of it. I assume it is > dying, > >> but thought to ask, as its rather new ( Power On Hours 827) its a > maxtor > >> 160gb. > > > > Time to file a warranty claim, I'm guessing. Maxtor has their own test > > utility, which you might as well download because they'll want an error > code > > from it before they do an exchange. > > > > > > Use smartctl: > > smartctl -a /dev/hda > > What does this show? > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact > [EMAIL PROTECTED] > >
