On Fri, Jul 27, 2007 at 12:30:28 -0400, Mitchell Laks wrote: > Hi, > I enjoy playing with sid :)
Don't we all? Unfortunately Sid sometimes enjoys playing with us as well... > I just updated to the latest sid on my Averatec Laptop 3250 running > amd processor > > which worked fine before. Now when I boot all is fine, i can surf > web using lynx if i stay in console mode. Then when i startx (i have > tried it with kde, gnome, xfce4-session session managers) and > immediately I get kernel errors and then i no longer can use the > network. I am connected by ethernet cable to my local network via eth0 > .... > > > Here are two examples of the the tail of dmesg for two different > kernels: > > (only stuff that happens after the startx > is invoked) : > > > here is dmesg using kernel 2.6.17-2-k7 > > dmesg|tail [...] > [drm] Initialized drm 1.1.0 20060810 > ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9 > PCI: setting IRQ 9 as level-triggered > ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKB] -> GSI 9 (level, > low) -> IRQ 9 > [drm] Initialized via 2.11.1 20070202 on minor 0 > agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. > agpgart: BIOS bug. AGP bridge claims to only support x4 rateFixing up > support for x2 & x1 > agpgart: Device is in legacy mode, falling back to 2.x > agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode > agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode > irq 11: nobody cared (try booting with the "irqpoll" option) > [<c014da62>] __report_bad_irq+0x36/0x75 > [<c014dc5a>] note_interrupt+0x1b9/0x1f7 > [<c014d1a3>] handle_IRQ_event+0x23/0x51 > [<c014e57f>] handle_level_irq+0x94/0xc5 > [<c010639e>] do_IRQ+0x57/0x71 > [<c010476b>] common_interrupt+0x23/0x28 > [<c01274dd>] __do_softirq+0x56/0xd3 > [<c012759f>] do_softirq+0x45/0x53 > [<c0127803>] irq_exit+0x38/0x6b > [<c01063a3>] do_IRQ+0x5c/0x71 > [<c010476b>] common_interrupt+0x23/0x28 > handlers: > [<de87795d>] (rhine_interrupt+0x0/0x654 [via_rhine]) > Disabling IRQ #11 > NETDEV WATCHDOG: eth0: transmit timed out > eth0: Transmit timed out, status 0003, PHY status 786d, resetting... > eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 > NETDEV WATCHDOG: eth0: transmit timed out > eth0: Transmit timed out, status 0003, PHY status 786d, resetting... [...] > I have tried booting with irqpoll option, no good, i have tried > noapic, no good. Other options to try are "pci=routeirq", "acpi=off" and "nolapic" (plus combinations of all of the above). [...] > I have tried to disable agp with agp=off in /boot/grub/menu.lst but > this did not help.. > > any ideas what i can do? Since this seems to be an interrupt problem it might help to see the output of cat /proc/interrupts before and after the network card fails. We also need to know what cards we are talking about exactly and which modules are loaded: lspci | egrep -i 'net|ether|vga|display|video' lsmod | egrep 'drm|agp|rhine' -- Regards, | http://users.icfo.es/Florian.Kulzer Florian | -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
