Hello,
On dual proc Xeon with dual ethernet Intel e1000, when I run a tcpdump,
according to network traffic my system freezes.
The console is dead, the only way to restore the system is an electric power
restart.
My configuration is :
# uname -a
Linux 2.6.8-2-686-smp #1 SMP Tue Aug 16 12:08:30 UTC 2005 i686 GNU/Linux
# lspci -vv
0000:02:04.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet
Controller (rev 05)
Subsystem: Dell: Unknown device 019a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 201
Region 0: Memory at fe9e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ecc0 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=2, DMOST=0, DMCRS=0, RSCEM-
0000:04:03.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet
Controller (rev 05)
Subsystem: Dell: Unknown device 019a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 209
Region 0: Memory at fe5e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dcc0 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=2, DMOST=0, DMCRS=0, RSCEM-
# ethtool -i eth0
driver: e1000
version: 5.2.52-k4
firmware-version: N/A
bus-info: 0000:02:04.0
# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: umbg
Wake-on: d
Current message level: 0x00000007 (7)
Link detected: yes
Do you have any idea ou clue on how to solve this ?
Thanks
Julien
