boot and dvd-writer problems From: [EMAIL PROTECTED] To: [EMAIL PROTECTED] Date: Today 15:23:25
Hello, I've installed Debian testing 2.6.18-3-486 on a PIV 2.8 GHz equiped with a dvd-rom and a dvd-writer. On bios the dvd drives are both present correctly, but when system startup and kde is running I can't find the writer: only dvd-rom is visible. I tried with wodim -scanbus but writer is not present and k3b says "Writer not found" I tried again on appending "hdc=ide-scsi" in menu.list for scsi emulation but no results. Here is dmesg: Linux version 2.6.18-3-686 (Debian 2.6.18-7) ([EMAIL PROTECTED]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-20)) #1 SMP Mon Dec 4 16:41:14 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. found SMP MP-table at 000f51d0 On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 126960 pages, LIFO batch:31 DMI 2.2 present. ACPI: RSDP (v000 IntelR ) @ 0x000f6d00 ACPI: RSDT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7100 ACPI: DSDT (v001 INTELR AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:2 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 15:2 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Detected 2805.371 MHz processor. Built 1 zonelists. Total pages: 131056 Kernel command line: root=/dev/sda2 ro mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512060k/524224k available (1543k kernel code, 11588k reserved, 574k data, 196k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5614.92 BogoMIPS (lpj=11229848) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20060707 CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5611.08 BogoMIPS (lpj=11222169) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 Total of 2 processors activated (11226.00 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=19 checking if image is initramfs... it is Freeing initrd memory: 4384k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb340, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0480-04bf claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2 Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 *12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 *9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 14 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:0b: ioport range 0x400-0x4bf could not be reserved PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: f8000000-f9ffffff PREFETCH window: e8000000-f7ffffff PCI: Bridge: 0000:00:1e.0 IO window: a000-afff MEM window: fa000000-fbffffff PREFETCH window: 30000000-300fffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered audit: initializing netlink socket (disabled) audit(1169296047.940:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Starting balanced_irq Using IPI No-Shortcut mode ACPI: (supports S0 S1 S3 S4 S5) Freeing unused kernel memory: 196k freed Time: tsc clocksource has been installed. ACPI: Fan [FAN] (on) ACPI: Thermal Zone [THRM] (40 C) usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 169, io base 0x0000bc00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected input: AT Translated Set 2 keyboard as /class/input/input0 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 177, io base 0x0000b000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 185, io base 0x0000b400 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 169, io base 0x0000b800 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb 1-1: new low speed USB device using uhci_hcd and address 2 ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 193, io mem 0xfc000000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected SCSI subsystem initialized libata version 2.00 loaded. 8139cp 0000:02:03.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip 8139cp 0000:02:03.0: Try the "8139too" driver instead. ata_piix 0000:00:1f.2: version 2.00 ata_piix 0000:00:1f.2: MAP [ P0 P1 IDE IDE ] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1f.2 to 64 8139too Fast Ethernet driver 0.9.27 ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14 scsi0 : ata_piix ata1.00: ATA-7, max UDMA/133, 240121728 sectors: LBA ata1.00: ata1: dev 0 multi count 16 ata1.00: configured for UDMA/133 Vendor: ATA Model: Maxtor 6Y120M0 Rev: YAR5 Type: Direct-Access ANSI SCSI revision: 05 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15 scsi1 : ata_piix usb 1-1: device not accepting address 2, error -71 ata2.00: ATAPI, max UDMA/33 ata2.01: ATAPI, max UDMA/33 usb 1-1: new low speed USB device using uhci_hcd and address 4 usb 1-1: configuration #1 chosen from 1 choice usb 1-2: new low speed USB device using uhci_hcd and address 5 usb 1-2: configuration #1 chosen from 1 choice usb 4-2: new full speed USB device using uhci_hcd and address 2 usb 4-2: configuration #1 chosen from 1 choice usbcore: registered new driver hiddev Initializing USB Mass Storage driver... input: HID 1267:c002 as /class/input/input1 input: USB HID v1.10 Mouse [HID 1267:c002] on usb-0000:00:1d.0-1 scsi2 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning USB Mass Storage support registered. input: USB Wheel Mouse as /class/input/input2 input: USB HID v1.00 Mouse [USB Wheel Mouse] on usb-0000:00:1d.0-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Vendor: SPRING Model: MultiCard Slot A Rev: 0100 Type: Direct-Access ANSI SCSI revision: 00 Vendor: SPRING Model: MultiCard Slot D Rev: 0100 Type: Direct-Access ANSI SCSI revision: 00 SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda:<5> Vendor: SPRING Model: MultiCard Slot S Rev: 0100 Type: Direct-Access ANSI SCSI revision: 00 Vendor: SPRING Model: MultiCard Slot M Rev: 0100 Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete sda1 sda2 sda3 < sda5 > sd 0:0:0:0: Attached scsi disk sda sd 2:0:0:0: Attached scsi removable disk sdb sd 2:0:0:1: Attached scsi removable disk sdc sd 2:0:0:2: Attached scsi removable disk sdd sd 2:0:0:3: Attached scsi removable disk sde ata2.00: qc timeout (cmd 0xa1) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata2.00: revalidation failed (errno=-5) ata2.00: limiting speed to UDMA/25 ata2: failed to recover some devices, retrying in 5 secs ata2.00: qc timeout (cmd 0xa1) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata2.00: revalidation failed (errno=-5) ata2: failed to recover some devices, retrying in 5 secs ata2.00: qc timeout (cmd 0xa1) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata2.00: revalidation failed (errno=-5) ata2.00: disabled ata2: failed to recover some devices, retrying in 5 secs ATA: abnormal status 0x58 on port 0x177 ata2.01: failed to IDENTIFY (I/O error, err_mask=0x40) ata2.01: revalidation failed (errno=-5) ata2: failed to recover some devices, retrying in 5 secs ata2.01: configured for UDMA/33 Vendor: HL-DT-ST Model: DVD-ROM GDR8162B Rev: 0015 Type: CD-ROM ANSI SCSI revision: 05 ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 177 eth0: RealTek RTL8139 at 0xa000, 00:e0:4c:bb:f1:af, IRQ 177 eth0: Identified 8139 chip type 'RTL-8100B/8139D' Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ts: Compaq touchscreen protocol output sr0: scsi3-mmc drive: 20x/48x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:1:0: Attached scsi CD-ROM sr0 sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: Attached scsi generic sg1 type 0 sd 2:0:0:1: Attached scsi generic sg2 type 0 sd 2:0:0:2: Attached scsi generic sg3 type 0 sd 2:0:0:3: Attached scsi generic sg4 type 0 sr 1:0:1:0: Attached scsi generic sg5 type 5 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 865 Chipset. agpgart: AGP aperture is 128M @ 0xe0000000 ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 201 input: PC Speaker as /class/input/input3 intel_rng: FWH not detected pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Unknown symbol acpi_run_oshp shpchp: Unknown symbol pci_hp_change_slot_info shpchp: Unknown symbol pci_hp_register shpchp: Unknown symbol pci_hp_deregister shpchp: Unknown symbol acpi_get_hp_params_from_firmware parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] Real Time Clock Driver v1.12ac shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 gameport: EMU10K1 is pci0000:02:04.1/gameport0, io 0xa800, speed 1104kHz ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 209 Adding 2915756k swap on /dev/sda5. Priority:-1 extents:1 across:2915756k EXT3 FS on sda2, internal journal loop: loaded (max 8 devices) SCSI Media Changer driver v0.25 device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL PROTECTED] NTFS driver 2.1.27 [Flags: R/W MODULE]. NTFS volume version 3.1. NTFS-fs warning (device sda1): load_system_files(): Unsupported volume flags 0x4000 encountered. NTFS-fs warning (device sda1): load_system_files(): Volume has unsupported flags set. Will not be able to remount read-write. Run chkdsk and mount in Windows. eth0: link down ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] [drm] Initialized drm 1.0.1 20051102 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169 [drm] Initialized radeon 1.25.0 20060524 on minor 0 agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode [drm] Setting GART location based on new memory map [drm] Can't use AGP base @0xe0000000, won't fit [drm] Loading R200 Microcode [drm] writeback test succeeded in 1 usecs usb 3-1: new full speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice scsi3 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning Vendor: Model: Rev: Type: Direct-Access ANSI SCSI revision: 00 SCSI device sdf: 2051809 512-byte hdwr sectors (1051 MB) sdf: Write Protect is off sdf: Mode Sense: 00 c0 00 00 sdf: assuming drive cache: write through SCSI device sdf: 2051809 512-byte hdwr sectors (1051 MB) sdf: Write Protect is off sdf: Mode Sense: 00 c0 00 00 sdf: assuming drive cache: write through sdf: unknown partition table sd 3:0:0:0: Attached scsi removable disk sdf sd 3:0:0:0: Attached scsi generic sg6 type 0 usb-storage: device scan complete On boot, system spend a lot of time on checking some ata2 devices: "ata2.00: qc timeout (cmd 0xa1) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata2.00: revalidation failed (errno=-5) ata2.00: limiting speed to UDMA/25 ata2: failed to recover some devices, retrying in 5 secs ata2.00: qc timeout (cmd 0xa1) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata2.00: revalidation failed (errno=-5) ata2: failed to recover some devices, retrying in 5 secs ata2.00: qc timeout (cmd 0xa1) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata2.00: revalidation failed (errno=-5) ata2.00: disabled ata2: failed to recover some devices, retrying in 5 secs ATA: abnormal status 0x58 on port 0x177 ata2.01: failed to IDENTIFY (I/O error, err_mask=0x40) ata2.01: revalidation failed (errno=-5) ata2: failed to recover some devices, retrying in 5 secs ata2.01: configured for UDMA/33 Vendor: HL-DT-ST Model: DVD-ROM GDR8162B Rev: 0015 Type: CD-ROM ANSI have I need to load some specific kernel modules? Thank you. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
