Johannes Wiedersich <[EMAIL PROTECTED]>: > Björn Lindström wrote: > >> I have two etch systems, one on a desktop, one on a laptop. I have the >> usb-storage module loaded on both. >> >> On the desktop, if I plug my camera (a Pentax Optio M20) in, I get a >> /dev/sda and a /dev/sda1 device. On the laptop I just see /dev/sda, >> and consequently can't mount it. Why would that be? > > Have you tried mounting it as root from a console?
The device /dev/sda1 still doesn't exist. > Have you looked at the output of 'fdisk -l' from both devices? When running that on /dev/sda with the camera attached there is no ouput. Now I notice there's some probably significant error messages showing up in dmesg: usb 2-1: new full speed USB device using uhci_hcd and address 24 scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 24 usb-storage: waiting for device to settle before scanning Vendor: PENTAX Model: DIGITAL_CAMERA Rev: 1.00 Type: Direct-Access ANSI SCSI revision: 02 usb 2-1: reset full speed USB device using uhci_hcd and address 24 usb 2-1: device descriptor read/64, error -84 usb 2-1: device descriptor read/64, error -84 usb 2-1: reset full speed USB device using uhci_hcd and address 24 usb 2-1: device descriptor read/64, error -84 usb 2-1: device descriptor read/64, error -84 usb 2-1: reset full speed USB device using uhci_hcd and address 24 usb 2-1: device descriptor read/8, error -84 usb 2-1: device descriptor read/8, error -84 usb 2-1: reset full speed USB device using uhci_hcd and address 24 usb 2-1: device descriptor read/8, error -84 usb 2-1: device descriptor read/8, error -84 usb 2-1: USB disconnect, address 24 sda : READ CAPACITY failed. sda : status=0, message=00, host=1, driver=00 sda : sense not available. sda: Write Protect is off sda: Mode Sense: 00 00 00 00 sda: assuming drive cache: write through sda : READ CAPACITY failed. sda : status=0, message=00, host=1, driver=00 sda : sense not available. sda: Write Protect is off sda: Mode Sense: 00 00 00 00 sda: assuming drive cache: write through sda : READ CAPACITY failed. sda : status=0, message=00, host=1, driver=00 sda : sense not available. sda: Write Protect is off sda: Mode Sense: 00 00 00 00 sda: assuming drive cache: write through sda:<3>Buffer I/O error on device sda, logical block 0 Buffer I/O error on device sda, logical block 0 unable to read partition table sd 4:0:0:0: Attached scsi removable disk sda usb-storage: device scan complete usb 2-1: new full speed USB device using uhci_hcd and address 25 usb 2-1: device descriptor read/64, error -84 usb 2-1: device descriptor read/64, error -84 usb 2-1: new full speed USB device using uhci_hcd and address 26 usb 2-1: device descriptor read/64, error -84 usb 2-1: device descriptor read/64, error -84 usb 2-1: new full speed USB device using uhci_hcd and address 27 usb 2-1: device descriptor read/8, error -84 usb 2-1: device descriptor read/8, error -84 usb 2-1: new full speed USB device using uhci_hcd and address 28 usb 2-1: device descriptor read/8, error -84 usb 2-1: device descriptor read/8, error -84 -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
