Thanks for the information so far.
I know it sounds strange, that I cannot change any settings in my BIOS,
unfortunately that is true - if anybody is interested I can prove it
with screenshots :-)
I already read the very same information in various articles. I tried to
unselect all unnecessary drivers, but it didn't help either. My CDROM
works fine, only after loading the wrong drivers I had some issues with
it, but that's pretty obvious.
I guess I will give the Etch CD a shot, haven't tried this so far.
Thanks for the advise.
If I don't find a solution, I will go ahead and buy an IDE drive to
install Debian to; I just can't believe, that I can't get it to work
with SATA and this really bugs me... :-)
Am I the only person who has problems installing Debian on SATA?
Simon
Dave Witbrodt wrote:
I'm new to the list and fairly new to Debian. I recently bought
myself a new PC (HP Pavilion a1320n) with a SATA drive. I know, that
there is an issue with the 2.4 kernel and I know that it is supposed
to work with the 2.6 kernel. For some reason I can't get it to work,
though. As soon as the installer tries to locate the HDD it fails
with an error message. I also tried to change the BIOS settings, as
some articles recommended, from "Normal" to "Combined" (SATA/PATA) -
however my BIOS does not have any settings I could change (concerning
the SATA drive). Some other linux distribution ("PC rescue CDs") were
able to detect and display the SATA drive.
I'm going to take a shot at this, though I'm no expert or guru.
I have a Dell Pavilion 8400 from last year, and it shipped with a
SATA150 drive. I was also not able to install Sarge until I altered
my BIOS settings from SATA/AHCI mode to UltraATA-emulation mode. It
sounds like your BIOS doesn't allow that, though I'm a bit surprised
if that's true. (No offense.)
There are two possibilities that I know of:
1) I read in different places about conflicts between CD drivers and
SATA drivers on the Sarge installation CDs. One link actually
provided instructions about temporarily removing a module until the
hard drive was partitioned, then restoring it.
The Sarge installer documentation also mentions a slightly
reminiscent problem:
SATA driver can block access to CD drive in installations
from CD. On systems having a SATA IDE controller that also
has the CD drive connected to it, you may see the installer
hanging during hardware detection for the CD drive or failing
to read the CD just afterwards. A possible reason is that the
SATA driver (ata_piix and maybe others) is blocking access to
the CD drive.
You can try to work around this by booting the installer in
expert mode and, in the "Detect and mount CD-ROM" step,
selecting only the drivers needed for CD support. These are
(ide-)generic, ide-cd and isofs.
The drivers needed to access the disk will still be loaded,
but at a later stage. By loading the CD drivers before the
SATA driver in this way, you may be able to complete the
installation. Note that CD-ROM access may still be an issue
after rebooting into the installed system.
(http://www.debian.org/releases/stable/debian-installer)
On the other hand, it's very possible that the kernel on the Sarge
installer CD simply doesn't have support for your hardware. I
actually was unable to install Sarge onto my older Pentium 3 machine
because I was using a PCI controller that would allow me to use larger
hard drives that my motherboard's controller could handle. The crazy
thing was that, even though the kernel on the CD couldn't recognize
the controller, when I installed Debian to a drive on the motherboard
controller the kernel _did_ recognize the PCI controller. I had to
move everything from the old hard drive to the new one.
2) If the Sarge CD can't do it, then you can try a recent Etch CD,
which has a newer kernel and is far more likely to recognize your
hardware. They've even got the Etch installers to work now! ;)
(For a long time, if you burned an Etch netinstall CD and tried to use
it, it just wouldn't work -- not without massive user intervention,
anyway.)
Dave W.
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
